Yamaha DVX-S200 - Manual (Page 68)

64
Creating the Best Listening Space
* CENTER
Sets whether the Center Speaker is present or not, and
sets the size of the Center Speaker.
Selection items: LRG (Large), SML (Small), NON
(None)
Default setting: SML
LRG: Select this setting when using a big Center
Speaker. The entire frequency band of the center
channel signal is output as it is from the Center
Speaker.
SML: Select this setting when using a small Center
Speaker. A center channel signal with a low tone
of 90 Hz or below is output from the speaker set
to * BASS.
NON: Select this setting when not using a Center
Speaker. The center channel signal distributes the
same volume level to the Front L/R Speakers.
* FRONT
Sets the size of the Front Speakers.
Selection items: LRG (Large), SML (Small)
Default setting: SML
LRG: Select this setting when using large Front
Speakers. The entire frequency band of the front
L/R channel signal is output as it is from the
Front Left and Right Speakers.
SML: Select this setting when using small Front
Speakers. A front L/R channel signal with a low
tone of 90 Hz or below is output from the speaker
set to * BASS.
* SUR.
Sets whether the Surround L/R Speakers are present or
not, and sets the size of the Surround L/R Speakers.
Selection items: LRG (Large), SML (Small), NON
(None)
Default setting: SML
LRG: Select this setting when using large Surround L/R
Speakers or when using Surround L/R Speakers
with surround subwoofers connected by speaker
cables.
The entire frequency band of the surround L/R
channel signal is output as it is from the Surround
Speakers.
SML: Select this setting when using small Surround L/R
Speakers. A surround L/R channel signal with a
low tone of 90 Hz or below is output from the
speaker set to * BASS.
NON: Select this setting when not using Surround L/R
Speakers. The surround L/R channel signal
distributes the same volume level to the Front L/
R Speakers.
* BASS
Selects the speaker to output a LFE/BASS (low tone)
signal.
Selection items: SWFR (Subwoofer), FRONT, BOTH
Default setting: SWFR
SWFR: Select this setting when using a Subwoofer.
The LFE and low tone (90 Hz and below)
sound from other channels, depending on *
CENTER, * FRONT and * SUR. settings, are
output from the Subwoofer.
FRONT: Select this setting when not using a
Subwoofer. The LFE and low tone (90 Hz and
below) sound from other channels, depending
on * CENTER, * FRONT and * SUR. settings,
are output from the Front L/R Speakers.
BOTH: Select this item to mix low frequence tones of
90 Hz and below with a LFE channel when
using a Subwoofer, independent of the Front
Speaker Sound mode setting.
The entire frequency band of the front L/R
channel is output from both the Front L/R
Speakers and Subwoofer. Sound can output
from the Subwoofer during 2-channel or
Dolby Surround playback.
* F. Level
Selects the Front Speaker level.
When the Front Speaker volume level is extremely high
and out of alignment with that of other speakers, you can
lower the volume level and regain a balance.
Selection items: Nrm (Normal), -10 dB
Default setting: Nrm
Nrm: Usually this setting is selected.
-10 dB: Use this setting if the output level of the Center
or Surround Speakers is out of alignment with
the Front Speakers. The volume level of the
Front Speakers decreases 10 dB (about 1/3).
• When “BOTH” is selected during Super Audio CD playback,
output is only from the subwoofer.
Advice
012DVX-S200-en 04.3.1, 11:18 AM 64