Yamaha CBX-K2 - Manual (Page 8)

8
Panel Controls and Terminals
■ Front Panel
q Keyboard
The CBX-K2 has a 49-key, 4-octave keyboard (C1 to C5),
featuring initial touch (velocity) control. All note on, note
off and velocity data is transmitted via the MIDI OUT
terminal. When used with the
C button, the keys are
used for changing various settings and sending special
MIDI messages. (Page 20.)
About the Functions of the CBX-K2: The functions are
divided into two groups: Group A and Group B. The
Group A and B functions are shown on the panel, above
the left section of the keyboard. Several functions can be
used by pressing only the relevant key; in other words,
pressing
L is not necessary. These functions, such
as Sequencer Stop and Start, are shown on the panel
without underline.
Functions whose names appear with a dashed underline
on the panel (for example, GM ON and XG ON) require
pressing
L.
The right section of the keyboard serves as value entry
and is used for those functions whose names are under-
lined on the panel and require value entry, such as
Program Change and Tempo.
Value entry on the CBX-K2 can be done in two number
systems: Decimal and Hexadecimal. The keys labeled A
through F are for Hexadecimal entry.
NOTE ■ The normal (default) velocity range of the
CBX-K2 is from 1 to 127. The range differs according
to the Touch Sensitivity setting (pages 19, 28).
SEQUENCER PROGRAM SYSTEM WHEEL ASSIGN
STOP
SONG SELECT
START TEMPO CONTINUE
B MEASURE TOP BOTTOM TIME SIGNATURE
FIXED VELOCITY MIDI CH MERGE ON/OFF SOUND OFF XG ON GM ON
VOICE MAP POLY/ MONO
BANK SELECT PROGRAM CHANGE
CHANNEL MERGE RESET CONTROL TG300B RESET SOUND OFF ALL CH DEVICE NUMBER TOUCH SENSITIVITY
RPN NRPN DRUM NUMBER CONTROLLER
RPN NRPN DATA DENSITY MSB 1ST/ LSB 1ST FOOT SW ASSIGN CONTROLLER
SLIDER ASSIGN
RPN NRPN DRUM NUMBER CONTROLLER
DATA DENSITY PB DENSITY
RESET TRANSPOSE
1 MODULATION 2 BREATH 5 PORTA TIME 6 DATA ENTRY 7 VOLUME 10 PANPOT
11 EXPRESSION 64 HOLD1(DAMPER) 65 PORTAMENTO 71 HARMONIC 72 RELEASE TIME 73 ATTACK TIME 74 BRIGHTNESS 84 PORTA CTRL
123 VIBRATO RATE 124 VIBRATO DEPTH 125 VIBRATO DELAY 126 LP FILTER CUTOFF 127 LP FILTER RESONANCE 128 HP FILTER CUTOFF 129 EQ LO GAIN 130 EQ HI GAIN
131 EQ LO FREQUENCY 132 EQ HI FREQUENCY 133 EG ATTACK TIME 134 EG DECAY TIME 135 EG RELEASE TIME 136 DRUM LP FILTER CUTOFF 137 DRUM LP FILTER RESONANCE 138 DRUM EG ATTACK RATE
139 DRUM EG DECAY RATE 140 DRUM PITCH COARSE 141 DRUM PITCH FINE 142 DRUM LEVEL 143 DRUM PAN 144 DRUM REVERB 145 DRUM CHORUS 146 DRUM VARIATION
147 DRUM HP FILTER CUTOFF 148 DRUM EQ LO GAIN 149 DRUM EQ HI GAIN 150 DRUM EQ LO FREQUENCY 151 DRUM EQ HI FREQUENCY
91 REVERB 93 CHORUS 94 VARIATION
120 PB SENSITIVITY
121 FINE TUNE
122 COARSE TUNE
CONTROLLER NUMBER LIST CONTROL CHANGE
ENTER
HEXA DECIMAL DECIMAL 1 2 3 4 5 6 7 8 9 A B C D E F 0 B
RPN
NRPN 152 CH PRESSURE 153 KEY PRESSURE 154 MASTER VOLUME 156 MASTER TUNING 157 VELOCITY 158 TEMPO
OTHERS
These non-underlined functions can be
used without pressing
L .
These underlined functions require
value entry and pressing
L .
These functions with dashed underline
need no value entry, but require pressing
L .
SEQUENCER
STOP
SONG
SELECT
START TEMPO CONTINUE
MEASURE TOP BOTTOM
TIME SIGNATURE
SEQUENCER
STOP
SONG
SELECT
START TEMPO CONTINUE
MEASURE TOP BOTTOM
TIME SIGNATURE
SOUND
OFF
XG
ON
GM
ON
RESET
CONTROL
TG300B
RESET
SOUND OFF
ALL CH
RESET
r t u y
w e q
i o