Yamaha X-V2600 User Manual

Page 100

SYSTEM OPTIONS

Zone2 Amplifier (Zone 2 amplifier)
Use to select how the Zone 2 speakers are amplified.
Choices: EXT, INT:Sur., INT:PRNS, INT:BOTH

• Select “EXT” if you want to connect your Zone 2

speakers through an external amplifier connected to the
ZONE 2 OUTPUT jacks on the rear panel of this unit.

• Select “INT:Sur.” to use the internal surround amplifier

of this unit if you want to connect your Zone 2 speakers
directly to the PRESENCE/ZONE 2(3) speaker
terminals on the rear panel of this unit.

• Select “INT:PRNS” to use the internal surround back

amplifier of this unit if you want to connect your Zone
2 speakers directly to the PRESENCE/ZONE 2(3)
speaker terminals on the rear panel of this unit.

• Select “INT:Both” to use the internal surround and

surround back amplifiers of this unit if you want to
connect you Zone 2 speakers directly to both the
PRESENCE/ZONE 2(3) and the SURROUND/ZONE
2(3) speaker terminals on the rear panel of this unit.

• If BI-AMP is set to ON in the ADVANCED SETUP menu,

INT:PRNS and INT:Both cannot be selected.

• Zone 2 and Zone 3 cannot use the same amplifier at the same

time. If INT:Both is selected for Zone2 Amplifier, for instance,
only EXT can be selected for Zone3 Amplifier and vice versa.

• The Intelligent Power AMP Assign feature of this unit becomes

in effect in the following cases so that the surround and
surround back amplifiers of this unit are automatically assigned
to the main room for the use of the surround back speakers
connected to the SURROUND BACK speaker terminals in the
7.1-channel system.
– When Zone2 Amplifier and Zone3 Amplifier are set to

INT:PRNS and EXT respectively and Zone 2 is turned off

– When Zone2 Amplifier and Zone3 Amplifier are set to EXT

and INT:PRNS respectively and Zone 3 is turned off

• If either Zone2 Amplifier or Zone3 Amplifier is set to INT:Sur.

or INT:PRNS, the speaker system of the main room is limited to
3.1 or 2.1-channel playback no matter when Zone 2 or Zone 3 is
turned off because the SURROUND/ZONE 2(3) speaker
terminals are used for the zone connection.

Zone3 Amplifier (Zone 3 amplifier)
Use to select how the Zone 3 speakers are amplified.
Choices: EXT, INT:Sur., INT:PRNS, INT:BOTH

• Select “EXT” if you want to connect your Zone 3

speakers through an external amplifier connected to the
ZONE 2 OUTPUT jacks on the rear panel of this unit.

• Select “INT:Sur.” to use the internal surround amplifier

of this unit if you want to connect your Zone 3 speakers
directly to the PRESENCE/ZONE 2(3) speaker
terminals on the rear panel of this unit.

• Select “INT:PRNS” to use the internal surround back

amplifier of this unit if you want to connect your Zone
3 speakers directly to the PRESENCE/ZONE 2(3)
speaker terminals on the rear panel of this unit.

• Select “INT:Both” to use the internal surround and

surround back amplifiers of this unit if you want to
connect you Zone 3 speakers directly to both the
PRESENCE/ZONE 2(3) and the SURROUND/ZONE
2(3) speaker terminals on the rear panel of this unit.

• If BI-AMP is set to ON in the ADVANCED SETUP menu,

INT:PRNS and INT:Both cannot be selected.

• Zone 2 and Zone 3 cannot use the same amplifier at the same

time. If INT:Both is selected for Zone2 Amplifier, for instance,
only EXT can be selected for Zone3 Amplifier and vice versa.

• The Intelligent Power AMP Assign feature of this unit becomes

INT:PRNS and EXT respectively and Zone 2 is turned off

– When Zone2 Amplifier and Zone3 Amplifier are set to EXT

and INT:PRNS respectively and Zone 3 is turned off

• If either Zone2 Amplifier or Zone3 Amplifier is set to INT:Sur.

Notes

Speaker B

Zone3 Amplifier

Zone2 Volume

Zone2 Amplifier

EXT

INT:Sur.

INT:PRNS