Wayne-Dalton 341785 - Manual (Page 3)

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.
To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com
3
Package Contents
DOOR sECTIONs (as REquIRED)
(2) VERTICal
TRaCk Rh/lh
(2) quICk INsTall Rh/lh
FlaGaNGlE (as REquIRED)
(2) Fully aDjusTablE Rh/lh
FlaGaNGlE (as REquIRED)
(2) hORIzONTal TRaCk Rh/lh
NOTE: DEPENDING ON ThE DOOR MODEl, sOME PaRTs
lIsTED WIll NOT bE suPPlIED IF NOT NECEssaRy. REaR
suPPORTs May OR May NOT bE INCluDED WITh yOuR DOOR.
ROllERs
(as REquIRED)
Pull ROPE
(IF INCluDED)
© Copyright 2006 Wayne-Dalton Corp. Part No. 325536 NEW 02/28/2006
Low Head Room Front Mount
Torsion Spring
Installation Instructions and Owner’s Manual
9800 Series - 3 Section
IMPORTANT NOTICE! Read these instructions carefully before
attempting installation. If in question about
any of the procedures, do not perform the
work. Instead, have a qualifi ed door agency
do the installation or repairs.
MaNual RIGhT & lEFT
END bEaRING bRaCkET
(1) CENTER bRaCkET
bushING
(1) CENTER bRaCkET
(2) TOP bRaCkET
WEaThER sEal & NaIls
(IF INCluDED)
q.I. jaMb bRaCkETs
(as REquIRED)
RIGhT aND lEFT
COuTNERbalaNCE CablE
DOOR sTOP & NaIls
(IF INCluDED)
RIGhT & lEFT DRuMs TORsION sPRINGs
(as REquIRED)
(1) OPERaTOR bRaCkET
1/4”-14 x 5/8” sElF TaPPING
sCREWs (as REquIRED)
5/16” x 1 5/8” hEx hEaD laG
sCREWs (as REquIRED)
3/8”- 16 hEx NuTs
(as REquIRED)
1/4”- 20 FlaNGED hEx
NuTs (as REquIRED)
1/4” - 20 x 9/16” TRaCk
bOlTs (as REquIRED)
(4) 1/4”-20 x 9/16” laRGE
hEaD RIbbED TRaCk bOlTs
(2) 5/16” FlaT
WashERs
(1) TORsION TubE
Fully aDjusTablE jaMb
bRaCkETs (as REquIRED)
(2) 3/8” FlaT
WashERs
(2) bOTTOM bRaCkETs
(2) COTTER PINs
(2) ClEVIs PINs
5/16” x 2” TaMPER PROOF laG
sCREWs (as REquIRED)
(2) 1/4”-20 x 5/8” TaMPER
REsIsTaNT sCREWs (as REquIRED)
3/8” -16 x 1-1/2” hEx hEaD
bOlTs (as REquIRED)
1/4”-20 x 5/8” sElF DRIllING
sCREWs (as REquIRED)
1/4”-20 x 7/8” sElF DRIllING
sCREWs (as REquIRED)