Timer recording – Toshiba SD-37VBSB User Manual
Page 28
28
2
4
1
3
TIMER REC SET
DATE
23 MON
11:30
--:--
3
START
END
CH
SELECT :
SET
:
EXIT
: MENU
SP
SPEED
OFF
PDC
23 MON
13:00
1
LP
OK : ENTER
14:30
TIMER REC SET
DATE
START
END
CH
SELECT :
SET
:
EXIT
: MENU
SPEED
OFF
PDC
--:--
--:--
------
--
--:--
--:--
--
------
--:--
--:--
--
------
--:--
--:--
--
------
--:--
--:--
------
--
--:--
--:--
------
--
--:--
--:--
------
--
--:--
--:--
------
--
/ ENTER
SELECT :
EXIT : MENU
-
-
-
-
-
-
-
-
....to be continued to next page
Timer recording
Timer recording can be programmed
on the TV-screen with the remote con-
trol. The built-in timer allows automatic
unattended recording of up to 8 pro-
grams within 1 month.
Notes:
• In the event of a power failure the data
of the automatic recording will be main-
tained in the built-in memory for about
30 minutes. Also, the clock will continue
to run for this period of time. Thereafter
the data will be deleted. When the
power resumes, the time display will
change to “--:--” that the timer setting
will have to be set.
• Not all TV Stations transmit PDC signal
all of the time, therefore it is advisable
to check before setting PDC to ON, if
you do set PDC to ON and no signal is
received your recording might not take
place at all. To check PDC status,
change to the channel on your DVD/
VCR you wish to record from, if the
word "PDC" appears on the screen for
a few seconds then that channel is
broadcasting PDC and you can set the
feature to ON.
Preparation
• Turn ON the TV and set to the AV input mode.
• Press VCR to select the VCR mode. (The VCR indicator will light.)
• Load a video cassette with the erase prevention tab intact. Make
sure with CALL that the time and date are correct.(see page 29).
Example: Timer recording for channel 1, 13:00 to 14:30 with Tape
speed LP on timer program number 1.
Press VCR MENU. Press
or
to select TIMER REC SET.
Then press ENTER.
Each line stands for one pro-
gram of the 8 memories. Select
one line with
or
. Then
press ENTER.
Set the desired date with
or
or Number buttons (0-9).
Then press
to accept it.
Set the Starting time (13:00),
ending time (14:30), channel
(1) and Tape speed (LP) in the
same way as the step 3.
• In case of an erroneous input
press
to go back to before
step and enter again.
TIMER REC SET
AUTO REPEAT
CH TUNING
SYSTEM SETUP
SELECT :
ENTER : ENTER
[OFF]
[AUTO]
MENU
EXIT
:
NICAM
To record with the PDC (Programme Delivery
Control) system
The PDC system starts recording
when it picks up a special signal
transmitted by the broadcaster
with the TV programme – even if
the TV programme starts early,
late or runs on longer than
scheduled. In step 4, press
▼
repeatedly until PDC OFF flashes,
then press
or
to display "ON" for recording with PDC.
23 MON
13:00
1
LP
OK : ENTER
14:30
TIMER REC SET
DATE
START
END
CH
SELECT :
SET
:
EXIT
: MENU
SPEED
ON
PDC
2J50101A [EN] P25-32
27/2/06, 5:39 PM
28