beautypg.com

Displaying information (status display), Operations using the menus (continued) – Toshiba Data TDP-T420 User Manual

Page 22

background image

4

4

Operations

Using the menus (Continued)

Default setting 2 menu

Item

Description

Projection
mode

Sets projection mode in accordance with Placement Style.

p.21

(Standard)

(Rear)

(Ceiling)

(Rear ceiling)

Fan mode

Sets the cooling fan speed.

Standard

High

Remote control When projectors are used and controlled by the remote control respectively,

this menu sets the code for the projector and the remote control.
[

or

: Enter setting] [

: Select from

1, 2

] [

: Confirm]

[

:Select

OK to end

]

Press [

Cancel] to return.

Key lock

Lock the control panel buttons.
[

or

: Enter setting] [

: Select

On/Off

] [

: Confirm]

[

:Select

OK to end

]

Press [

Cancel] to return.

Lamp power

Set the lamp power.

Low

Standard

Reset all

Press

. (The password and user logo are not reset.)

Resets all adjustments and settings to their factory settings.

Yes

No

Password

Password setting

p.33

Press

. Password registration/Password setting

Detailed description

[Fan mode]

Setting [

Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise

gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500
meters above sea level).

Do not set Fan mode to [

High] when using the projector at a lower altitude.

[Remote control]

Sets a remote control code from types. You can set each code respectively for up to
projectors. The factory setting is [

1].

To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.

You cannot operate the remote control if the codes of the projector and the remote
control do not match.

Remote control code setting for remote control

Set the same

remote control code switch as the projector.

p.16

p.17

[Key lock]

Protect from operating errors by locking on the control panel buttons of the projector.
(The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly operation
with the control panel buttons is disabled.

To release the key lock, set the [

Key lock] to [Off] using remote control. Pressing

the [

RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off].

(When operating the main unit, the indicators of LAMP and TEMP light in orange
for seconds, and at the same time the projector beeps.).

[Lamp power]

When [

Lamp power] is set to [Low], the screen becomes a little darker, but the cooling

fan noise gets quieter.

Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item

Description

Digital (DVI) Analog (D-SUB)(DVI)

Video S-video

RGB Y/P

B

/P

R

RGB Y/P

B

/P

R

Input

Input source name

Yes

Yes

Yes

Yes

Yes

Yes

Mode name

RGB input mode

[Note 1]

Yes

No

Yes

No

No

No

Resolution

Resolution (in dots)

Yes

No

Yes

No

No

No

Frequency

Sync frequency

Yes

No

Yes

No

No

No

Sync

Sync signal polarity

[Note ]

Yes

No

Yes

No

No

No

Signal format

Y/P

B

/P

R

signal format

No

Yes

No

Yes

No

No

Video mode

Color method of video signal

No

No

No

No

Yes

Yes

Lamp time

Time of lamp use

[Note ]

Yes

Yes

Yes

Yes

Yes

Yes

Lamp reset count

The count for lamp replacement Yes

Yes

Yes

Yes

Yes

Yes

Total time

The total time that this
projector is used.

Yes

Yes

Yes

Yes

Yes

Yes

Version

Firmware version

[Note 4]

Yes

Yes

Yes

Yes

Yes

Yes

Notes

1: The mode of supported RGB signals

p.53

is shown.

: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
: Displays [

Lamp time] as a measure of when the lamp should be replaced. (Cannot be

used as a counter of guaranteed lamp time.) When the displayed time approaches ,000
hours, consult with a dealer about getting replacement for:

TLPLW40 (sold separately).

4: [

Version] shows the version of the projector’s internal control program. This version will

be requested for customer service purposes.

Note

The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.