beautypg.com

Operating a computer using the remote control, Placement, Preparations – Toshiba Data TDP-T420 User Manual

Page 11

background image

20

21

Preparations

Operating a computer using the remote control

A computer can be operated using the projector’s remote control. This function is available on
any computer with the Windows

®

98/98SE, Windows

®

Me, Windows

®

2000, Windows

®

XP, or

Windows Vista

®

OS, that is equipped with a USB port which can support USB1.1 (The mouse

remote control receiver is also supported on OS 9 or OS X for the Macintosh). However,
please note that Toshiba does not guarantee the operation of all computers.

1

Connecting a computer

Connect the mouse remote control receiver (supplied) to a computer.

Mouse remote control receiver

To USB port

The remote control may fail to operate

if the mouse remote control receiver

is exposed to bright sunlight or

fluorescent lighting.
In such a case, change position or

direction of the mouse remote control

receiver and retry.

2

Operating a computer

Operate remote control’s buttons towards the mouse remote control receiver.

Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
To left click
Press the L-CLICK button.
To right click
Press the R-CLICK button.
To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
Using the computer’s page up [#] and down [$] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint

®

slides.

Mouse control

Remote Control Front Remote Control Rear

PAGE –

PAGE +

R-CLICK

L-CLICK

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is “floor-mounted front projection.” Set the [

Projection mode] in the

Default setting 2 menu

p.42

, in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

Ceiling-mounted front projection

Ceiling-mounted rear projection

wARNING

Always obey the instructions listed in IMPORTANT SAFeTY INSTRUCTIONS

when placing the unit. Attempting to clean and replace the lamp in a high location

by yourself may cause you to fall, resulting in injury.

If you wish to mount the projector on the ceiling, be sure to ask your dealer

to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold

separately) and specialized knowledge. Improper mounting could cause the projector

to fall, resulting in an accident.

If the projector is ceiling-mounted, install the breaker for turning off the power in

case of anomaly. Let everyone involved with the use of the projector know that fact.

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection distance.

(Projection sizes are approximate values for full-size picture with no keystone adjustment.)

Placement

a is the distance (mm, feet) between the lens and the

screen, and corresponds to a range of 580 mm (1.90

ft.) to 1501 mm (4.93 ft.).

H is the height from the image

bottom to the center of the lens.

a = 0.00375 × projection size (inches)

2

+

14.815 × projection size (inches) – 18.3

Projection size

Projection

distance

a

Height (

H)

40 inches

580 mm (1.90 ft.) 91.4 mm (0.30 ft.)

50 inches

732 mm (2.40 ft.) 114.3 mm (0.38 ft.)

60 inches

884 mm (2.90 ft.) 137.2 mm (0.45 ft.)

80 inches

1191 mm (3.91 ft.) 182.9 mm (0.60 ft.)

100 inches

1501 mm (4.93 ft.) 228.6 mm (0.75 ft.)

90°

As seen from above

As seen from the side

Screen

Lens center

a

90°