Toshiba RD-XV48KE - Manual (Page 85)

85 EN
Symptom Remedy
CHA
NNE
L
TV channels cannot be changed. • Check if the connections are made securely and correctly.
• Check if the cables are damaged.
• Try “Channel” setting by following the steps on pages 22-23.
Only specific channels do not appear. • The channels may be set to be skipped. (See page 23.)
The external input channels (such as AV2 or
AV3) cannot be skipped. • This unit does not skip the external input channels. This is not a
malfunction.
RECORDING
GENERAL
The image from the external device cannot be
displayed. • Try pressing [INPUT SELECT F] repeatedly.
• Turn on all connected devices.
• Check if the connections are made securely and correctly.
HD
D /
D
V
D
Recording is impossible. • It is prohibited to make a recording from 2 minutes before the
programmed start time of a timer recording.
• This unit cannot record programmes that contain copy protection signal.
This is not a malfunction.
• The space of the recording media may be used up. Try deleting
unnecessary titles, or exchange it with the recordable media.
• The maximum number of titles or chapters has exceeded. Delete the
unnecessary titles to make enough space or insert a new recordable
media.
• Check if the connections are made securely and correctly.
Timer recording cannot be performed. • The internal clock of the unit may have been stopped due to a power
failure that lasted for more than 30 seconds. Reset the clock. (See page
25.)
DV
D
Recording is impossible. • Check if the disc is CPRM compatible. Copy-once programmes can only
be copied onto the disc which is CPRM compatible.
• Check if the disc is protected or finalised. Undo the protection or the
finalisation.
• Video mode DVD-RW once formatted in other unit cannot be recorded in
this unit unless formatted in this unit.
• Check if the connections are made securely and correctly.
“Repairing” appears on the TV screen. • If there is a power failure or unplugging during recording, finalising,
formatting or editing (even after “Repairing” disappears), a repairing
process will begin automatically just after turning the unit on again.
• It may take several minutes up to about several hours.
In a case you intend to cancel the repairing
process. • If you intend to cancel the repairing process, press [A OPEN \CLOSE]
on the front panel, then select “Yes” and press [ENTER]. After that,
press [OPEN
\CLOSE A] to take out the disc. The disc cancelled during
the repairing process MAY NOT work.
The indication
“
” does
not disappear.
• “ ” may remain on screen for the
maximum of 20 seconds even after it reached 100%. This is not a
malfunction.
VCR
Recording does not start immediately after
pressing [REC I]. • Make sure the videotape has a recorded tab when you record to a
videotape. If needed, cover the hole with cellophane tape.
P
L
A
Y
BAC
K
GE
NERAL
TV aspect ratio does not match your TV
screen. • Check “TV Aspect” setting. (See page 78.)
• A different aspect ratio will be used when the aspect ratio specified by
the disc is not supported by this unit.
Playback picture is distorted.
Colour of the picture is abnormal. • During fast forward or fast reverse, playback picture may be distorted.
This is not a malfunction.
• Connect to TV directly. When you connect this unit with the television via
VCR or other devices, the picture may be distorted due to the copy-
protection signal.
• Check if the cables are damaged.
• Keep the equipment which may cause electrical disturbances, such as a
cellular phone, away.
There is no sound, or no subtitle. • Turn on all connected devices.
• Check if the external input channel is set correctly.
• Check if the connections are made securely and correctly.
• If using the HDMI connection, sound is not output when “HDMI Audio” is
set to “OFF”.
• Check the RCA audio cable connection. If you are using HDMI-DVI
conversion cable, you must connect the RCA audio cable, too.
• If using the HDMI connection, check whether the output format of this
unit (HDMI FORMAT) matches the supported input format of other
connected device.
Repairing
Repairing
Do you want to cancel a repairing
process? When selecting “Yes”,
the disc may not be usable.
Yes
No
100% Writing to Disc
100% Writing to Disc
In
trod
ucti
on
Con
n
e
c
tio
n
s
B
asi
c Se
tu
p
P
la
y
b
ack
Ed
iti
n
g
Ot
h
e
rs
Fu
nc
ti
on
S
e
tup
Reco
rdi
n
g
V
CR Fu
nct
ion
s
E3LG0ED_EN.book Page 85 Wednesday, April 30, 2008 11:52 AM