Toshiba TDP-TW355 - Manual (Page 28)

55
Operations
54
Setting up the wireless LAN (Continued)
● Details on individual items
• [Easy Connect (USB)]
This feature allows users to easily connect the projector to a computer over wireless
networks, without making
Network settings via Wireless Utility .
• [Network settings]
< Mode >
Your projector is set to Ad hoc in the factory. Change the setting if you want to use the
projector in Infrastructure mode.
< Channel >
Usually, you do not have to set this item. If a network group having the same SSID
already exists in the projector’s coverage, the channel is changed automatically to the
channel of that network group.
Note 1: If a set channel is in bad connections for wireless connection, try the other
channels to avoid the effects of radio waves to select the one in possibly the
best communication conditions.
Note 2: To communicate in Ad hoc mode with a computer that cannot change the
channel, start up the projector before the computer.
< SSID >
This is an ID code for connecting to specific individuals over a wireless LAN. This may
also be called “
Network group ” or “ Network name ”. Please read the following carefully.
Note 1: The SSID is set to TDPJ when shipped from the factory. If you leave this setting
as it is, security may be compromised due to access by a third party using the
“
Wireless Utility ” within the projector’s possible communication area. Before
using the projector, therefore, be sure to set SSID to a character string different
from the default.
Note 2: When you use the Ad hoc communication mode, if there is a similar SSID
network group (for example TDPJ, TDPJ1, TDPJ2, etc.) in the possible
communication area, it is possible that your projector name will not be dis-
played in the
Wireless Utility projector list column. If this is the case, set SSID
to a completely different character string.
< Encryption >
Enable or disable encryption for security purposes.
Note: Encryption is factory-set to Off . If you use the projector with this setting left
unchanged, security may be compromised due to access by a third party using
the Wireless Utility within the projector’s coverage. Before using the projector,
therefore, be sure to set
Encryption to On .
< WEP key >
When you have set Encryption to On , the WEP key must be set. For use at an
encryption level of 64-bit , specify a string of 5 arbitrary characters or a string of ten
characters in hexadecimal notation. For use at the 128-bit level, specify a string of 13
arbitrary characters or a string of 26 characters in hexadecimal notation.
Note: Alphabetic characters (A to F, a to f) used in hexadecimal notation are case
insensitive; the uppercase characters and their lowercase equivalents are
handled to be identical.
■ Setting Wireless Utility
If you select Wireless Utility , the following items can be set.
[Yes No] [Enter: ]
Mode: Ad hoc Infrastructure
Channel: Select a number (1 to 11) using the buttons.
SSID: Specify a desired character string (1 to 32 characters).
[ : Move left or right one character.] [ to :
Set a character.]
Encryption: On Off
WEP key: Specify a desired character string.
(5 to 13 characters, or 10 to 26 digits in hexadecimal notation)
[ : Move left or right one character.] [ to :
Set a character.]
DHCP: Use Not use
IP address: Enter using the numeric keys of the remote control.
[ : Move left or right one character.] [ to :
Set a character.]
Subnet mask: Enter using the numeric keys of the remote control.
[ : Move left or right one character.] [ to :
Set a character.]
Gateway: Enter using the numeric keys of the remote control.
[ : Move left or right one character.] [ to :
Set a character.]
Confirm: [OK] [Cancel] [Enter: ]
Reset all the network settings.
Confirm: [Yes] [No] [Enter: ]
Specify a desired character string (0 to 8 characters).
[ or : Enter setting mode.] [ : Select item.] [ :
Move left or right one character.] [ to : Set a character.]
Confirm: [OK] [Cancel] [Enter: ]
Specify whether to allow the remote control of the projector from a
computer.
Allowed Presentation Forbidden
Allowed:
The projector always accepts remote commands
from a computer.
Presentation: Accepts only the remote commands from the
computer whose screen is currently displayed via
the projector (Update automatically) using Wireless
Utility.
Forbidden: Always ignores any remote commands from a
computer.
Browser authentication: Switch on/off the password
authentication for access to the setting screen using the
Projector Configuration Tool.
Password: Enter the password used to access the setting
screen when the Browser authentication is set to On. A
character string (1 to 8 characters) can be specified as desired.
[ : Move left or right one character.] [ to : Set a
character.]
Confirm: [OK] [Cancel] [Enter: ]
Description Item
Easy Connect (USB)
Network settings
Setting
initialization
Projector
name
Remote
control
WEB browser
On Off
* To enter characters, use the numeric keypad on the remote control.