Roland RS-50 - Manual (Page 95)

95
Performing with an external MIDI device
Performing with an
external MIDI device
Setting the patch receive channel
When you have finished connecting the external MIDI device, match
RS-50’s Receive channel with the external MIDI device’s Transmit
channel. Here we will explain the settings for using the RS-50 in
Patch mode.
* If you are using the RS-50 in Performance mode, the part and channel
numbers will be the same unless you change the settings.
1. Press [SYSTEM] so it is lit.
2. Use PAGE/CURSOR [ ]/[ ] to select “Patch Rx Ch”
(patch receive channel).
fig.r10-11_40
By holding down [SHIFT] and using PAGE/CURSOR [ ]/
[ ] you can quickly select the “SYSTEM|MIDI” group (p. 90).
3. Use VALUE [-]/[+] to modify the value.
VALUE
1–16: Performance data of each part will be received on
the selected channel.
Setting the program change receive
switch
Then, to enable tones to be switched from the external MIDI device,
set the Receive Switch for Program Change and Bank Select to ON.
Factory settings have these set to ON.
1. Press [SYSTEM] so it is lit.
2. Use PAGE/CURSOR [ ]/[ ] to select “Rx Prog Chg”
(Receive Program Change Switch) and “Rx Bank Sel”
(Receive Bank Select Switch).
3. Use VALUE [-]/[+] to set both parameters to “ON.”
4. Press [WRITE] to save the settings.
For further information, refer to “How to make the system
function settings” (p. 88).
Press [EXIT] to cancel the operation and return to the previous page.
* For instructions on setting the external MIDI device’s Transmit
channel, refer to the owner’s manual for that device.
* If you are using Performance mode, you will also need to set “Receive
Sw,” “Receive Prg Chg,” and “Receive Bank Sel” for each part in
addition to the settings described above (p. 57).
Selecting RS-50 sounds from an
external MIDI device
Transmitting Bank Select (Controller Numbers 0 & 32) and Program
Change messages from the external MIDI device to the RS-50 allows
you to switch patches and rhythm sets.
1. Transmit a value for the Bank Select MSB (controller number
0) (BnH 00H mmH) message to the RS-50.
2. Transmit a value for the Bank Select LSB (controller number
32) (BnH 20H llH) message to the RS-50.
3. Transmit a Program Change (CnH ppH) to the RS-50.
n: MIDI channel number
mm, ll: Bank number
pp: Program number
The “Perform Ctrl Ch” (Performance Control Channel) setting
lets you switch performances in Performance mode. With the
factory settings, this is set to “OFF”; performances will not be
switched.
Bank number/program number
correspondence table
The MIDI messages transmitted by an external MIDI device
correspond with patches/rhythm sets on the RS-50 as shown in the
following table.
* If the Program numbers on your external MIDI device are referenced as
values from 0 to 127, find the appropriate number by subtracting 1
from the number in the following correspondence chart.
* When the RS-50 receives a Program Change message without receiving
the Bank Select, it switches to the patch or rhythm set with the same
Bank number as the currently selected patch or rhythm set.
For details on how numbers in the table correspond to the sound
of the RS-50, refer to
“Patch list” (p. 111).
Performance
Patch
Group Number Bank Number Program
Number
MSB LSB
User 001–008 085 000 001–008
Preset 001–032 085 064 001–032
Group Number Bank Number Program
Number
MSB LSB
User 001–128 087 000 001–128
Preset 001–128 087 064 001–128
129–256 087 065 001–128
257–384 087 066 001–128
385–512 087 067 001–128
513–640 087 068 001–128
GM Patch 001–256 121 000– 001–128
RS-50_e3.book 95 ページ ２００３年１１月７日 金曜日 午後７時１分