Pioneer Elite SC-35 - Manual (Page 96)

Controlling the rest of your system (In case of SC-35) 10
96
En
Controlling the rest of your system
(In case of SC-35)
Important
• This section includes explanations for the SC-35’s
remote control. For instructions for the SC-37’s
remote control, see Controlling the rest of your
system (In case of SC-37) on page 83.
About the Remote Setup menu
The Remote Setup mode is set by pressing the number
button while pressing R.SETUP. The different items on
the Remote Setup menu are described below. For their
setting procedures, refer to the explanations for the
respective items.
Note
• You can cancel or exit any of the steps by pressing
R.SETUP.
• After one minute of inactivity, the remote
automatically exits the operation.
Operating multiple receivers
Up to four receivers can be operated discretely using this
receiver's remote control when using multiple receivers,
provided they are of the same model as this receiver. The
receiver to be operated is switched by inputting the
preset code to set the remote control setting.
• Set the remote modes on the receivers before using
this function (see Remote Control Mode Setup on
page 119).
1 Press and hold R.SETUP, then press “4” for three
seconds.
The LED flashes continuously.
• To cancel the preset setup mode press R.SETUP.
2 Press the number button for the receiver (“Receiver
1” to “Receiver 4”) you wish to operate.
For example, to operate “Receiver 2”, press “2”.
If the LED lights for one second, the setting has been
successfully completed.
When the preset code is input, the LED flashes three
times to indicate that the setting has failed.
Setting What it does
Preset
recall Preset codes can be set for the various input
functions. The remote control codes of a number
of other devices (including products of other
brands) are preset in the remote control to allow
these devices to be operated. See “Selecting
preset codes directly” on page 97.
Code
learning If the desired operations cannot be performed
even though you have set the preset codes, the
remote control signals of other devices can be
learned directly. See “Programming signals from
other remote controls” on page 97.
Multi
operation A series of the remote control operations for
starting listening or viewing can be programmed.
Multiple remote control codes can be set for the
different input functions. See “Multi operation and
System off” on page 99.
System off This is a function for automatically turning off the
power of devices connected to the receiver.
Multiple remote control codes can be set, as
desired. See “Multi operation and System off” on
page 99.
Direct
function This is a setting for changing only the remote
control unit’s operation screen, without changing
the receiver’s input, when the remote control
unit’s input function buttons are pressed. This is
convenient for using the remote control unit for
devices not connected to the receiver. See “Direct
function” on page 98.
Erase
learning This function is used to erase remote control
codes that have been learned. Codes learned for
the different input functions can be erased
individually. See “Erasing one of the remote
control button settings” on page 98.
Back light The backlight lighting pattern can be selected
from among four modes, in consideration of
convenience and battery service life. See “Setting
the backlight mode” on page 99.
Reset
function This is a function for resetting preset codes that
have been set. Key resetting can be done for
individual input functions. See “Erasing all learnt
settings that are in one input function” on page 98.
All reset This is a function for resetting all remote control
unit settings you have made to the defaults set
upon shipment from the factory. See “Resetting
the remote control settings” on page 101.
Change RC
mode If you have multiple Pioneer receivers, amplifiers,
etc., this setting can be used to prevent other units
from operating simultaneously when the remote
control unit is operated. See “Operating multiple
receivers” on page 96.
Setting What it does
SC-37_35_UXJCB.book 96 ページ ２０１０年３月９日 火曜日 午前９時３２分