Pioneer Elite SC-35 - Manual (Page 58)

Basic playback 05
58
En
Pairing the Bluetooth ADAPTER and Bluetooth
wireless technology device
“Pairing” must be done before you start playback of
Bluetooth wireless technology content using the
Bluetooth ADAPTER. Make sure to perform pairing the
first time you operate the system or any time pairing data
is cleared. The pairing step is necessary to register the
Bluetooth wireless technology device to enable Bluetooth
communications.
1 For more details, see also the
operating instructions of your Bluetooth wireless
technology device.
1 Set the remote control to the receiver operation
mode, then press HOME MENU.
2 Select ‘System Setup’, then press ENTER.
3 Select ‘Other Setup’, then press ENTER.
4 Select ‘Pairing Bluetooth Device’, then press
ENTER.
5 Select the ‘Passcode’ setting you want.
Select the same passcode as the Bluetooth wireless
technology device you wish to connect.
• 0000/1234/8888 – Select the passcode from these
options. These are the passcodes that can be used in
most cases.
• Others – Select to use a passcode other than those
mentioned above.
6 If you selected Others in step 5, enter the passcode.
Use / to select a number and / to move the
cursor.
7 Follow the instructions displayed on the GUI screen
to conduct pairing with the Bluetooth wireless
technology device.
Switch on the Bluetooth wireless technology device that
you want to make pair, place it near the receiver and set
it to the pairing mode.
8 Check to see that the Bluetooth ADAPTER is
detected by the Bluetooth wireless technology device.
When the Bluetooth wireless technology device is
connected:
CONNECTED appears in the receiver display.
2
When the Bluetooth wireless technology device is not
connected:
Go back to the passcode setting in step 5. In this case,
perform the connection operation from the Bluetooth
wireless technology device.
9 From the Bluetooth wireless technology device list,
select Bluetooth ADAPTER and enter the Passcode
selected in step 5.
3
Listening to music contents of a Bluetooth
wireless technology device with your system
1 SC-37 only: Set the remote control operation
selector switch to SOURCE.
2 Press ADAPTER on the remote control to switch the
receiver to ADAPTER PORT input. 4
3 From the Bluetooth wireless technology device,
perform the operation to connect to the Bluetooth
ADAPTER.
4 Start playback of music contents stored on the
Bluetooth wireless technology device.
This receiver’s remote control buttons can be used for
basic playback of files stored on Bluetooth wireless
technology devices.
5
SC-37:
SC-35:
The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their
respective owners.
Note
1 • Pairing is required when you first use the Bluetooth wireless technology device and Bluetooth ADAPTER.
• To enable Bluetooth communication, pairing should be done with both your system and Bluetooth wireless technology device.
2 The system can display alphanumeric characters only. Other characters may not be displayed correctly.
3 The passcode may in some cases be referred to as PASSKEY or PIN code.
4 When the Bluetooth ADAPTER is not plugged into the ADAPTER PORT, NO ADAPTER will be displayed if ADAPTER PORT input is selected.
5 • Bluetooth wireless technology device should be compatible with AVRCP profile.
• Depending on the Bluetooth wireless technology device you use, operation may differ from what is shown in the remote control buttons.
SOURCE
TV RECEIVER
VOL
VOL CH
STATUS
THX PQLS MPX MEMORY
PHASE CTRL CH LEVEL
PGM MENU
STEREO
AUTO/ALC/
DIRECT STANDARD ADV SURR
HDMI OUT
TV / DTV MPX PQLS
PHASE CTRL STATUS THX
STEREO DIRECT STANDARD ADV SURR
AUDIO
HDD DVD
2 1 3
SC-37_35_UXJCB.book 58 ページ ２０１０年３月９日 火曜日 午前９時３２分