Pioneer Elite SC-35 - Manual (Page 42)

Connecting your equipment 03
42
En
Switching components on and off using
the 12 volt trigger
You can connect components in your system (such as a
screen or projector) to this receiver so that they switch on
or off using 12 volt triggers when you select an input
function. However, you must specify which input
functions switch on the trigger using the The Input Setup
menu on page 45. Note that this will only work with
components that have a standby mode.
• Connect the 12 V TRIGGER jack of this receiver to
the 12 V trigger of another component.
Use a cable with a mono mini-plug on each end for the
connection.
After you’ve specified the input functions that will switch
on the trigger, you’ll be able to switch the component on
or off just by pressing the input function(s) you’ve set on
page 45.
It is also possible to have the component switch not when
the input function is switched, but when HDMI OUT is
switched. For details, see HDMI Setup on page 73.
Plugging in the receiver
Only plug in after you have connected all your
components to this receiver, including the speakers.
1 Plug the supplied power cord into the AC IN socket
on the back of the receiver.
2 Plug the other end into a power outlet.
1
CAUTION
• Handle the power cord by the plug part. Do not pull
out the plug by tugging the cord, and never touch the
power cord when your hands are wet, as this could
cause a short circuit or electric shock. Do not place
the unit, a piece of furniture, or other object on the
power cord or pinch the cord in any other way. Never
make a knot in the cord or tie it with other cables. The
power cords should be routed so that they are not
likely to be stepped on. A damaged power cord can
cause a fire or give you an electric shock. Check the
power cord once in a while. If you find it damaged,
ask your nearest Pioneer authorized independent
service company for a replacement.
• Do not use any power cord other than the one
supplied with this unit.
• Do not use the supplied power cord for any purpose
other than that described below.
• The receiver should be disconnected by removing the
mains plug from the wall socket when not in regular
use, e.g., when on vacation.
• Make sure the blue  STANDBY/ON light has gone
out before unplugging.
• If you have connected speakers with a 6 Ω
impedance, change the impedance setting before
turning on the power.
12 V
TRIGGER
1
2
(OUTPUT
12 V
TOTAL
150 mA MAX)
RS-232C
HDMI
ASSIGNABLE
COMPONENT VIDEO
ASSIGNABLE
MONITOR OUT
ZONE 2 OUT
IN
Y
ANTENNA
FM UNBAL 75 AM LOOP
CD
IN
VIDE
MONITOR
OUT
ZONE2
OUT
ZONE3
OUT
DVD
IN
TV/SAT
IN
VIDEO
IN
DVR/BDR PHONO
IN OUT IN
P R P B
1
IN BD IN 1 IN 2 IN 3
OUT 1 (CONTROL) OUT
1 4
(DVD)
IN 2 (DVR/BDR)
IN 3 (VIDEO)
CONTROL
CU-RF100
IR
IN
IN
IN OUT
OUT
1
2
IN 4
(OUTPUT 5 V
150 mA MAX)
SPEAKERS
Class 2 Wiring
SIGNAL GND
R
FRONT HEIGHT/W
SEE INSTRUCTION
MANUAL
SELECTABLE
VOIR LE MODE
D'EMPLOI
SELECTABLE
12 V TRIGGER
INPUT
Note
1 After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins. You cannot carry out any
operations during this process. The HDMI indicator in the front panel display blinks during this process, and you can turn on this receiver
once it has stopped blinking. When you set the Control with HDMI to OFF, you can skip this process. For details about the Control with HDMI
feature, see Control with HDMI function on page 72.
SC-37_35_UXJCB.book 42 ページ ２０１０年３月９日 火曜日 午前９時３２分