Philips LC5241 - Manual (Page 19)

DATA MODE - ADVANCED MENU
Press the Menu button with the flip cover of the remote control
open, to display the advanced menu. Use the cursor key
(up/down) to select the display and picture control functions. After
selection of the required function, set the required value setting
by means of the cursor key (left /right).
IMAGE (Picture control)
–
BRIGHTNESS
Adjusts brightness of the displayed picture;
– CONTRAST
Adjusts the overall contrast intensity;
– PICTURE ADJ. (Size)
Adjusts the computer image in a horizontal direction to make
the image completely fit the screen. Adjustment is performed
in dot units. Adjust to the position where vertical flicker
disappears.
The HORIZONTAL SIZE function is used to size a computer
image to make it fit the projected picture, both horizontally and
vertically. The horizontal size parameter has permanent scope.
When the OSD menu is active and the horizontal size option is
selected, the level will be indicated graphically on a linear scale
(gauge). The default output level conforms to the value set by
the Auto image function. Switching to another data mode
automatically restores Auto image if the data mode is not part
of the ten most recently used display modes;
– FINE PICTURE (Phase)
Press the cursor key to the left or right and adjust to minimize
image noise, flicker, color variations, etc.;
– POSITION
Adjusts the computer image in horizontal and vertical direction
to centre it on the screen.
To activate the POSITION setting, press the OK button on the
remote control when POSITION is addressed in the IMAGE
setting menu. With the cursor key you can move the picture in
the required position.
COLOR
–
V-EFFECT
The following can be selected.
- NORMAL is standard setting
- NATURAL stresses coloring
- REAL stresses brightness
- CUSTOM is used to adjust freely as desired. Personal setting
can be made of the color gamma index, and the respective
R,G and B levels.
To activate the CUSTOM setting, press the OK button on the
remote control when CUSTOM is addressed in the COLOR
setting menu. With the cursor key you can make your
desired personal setting;
– COLOR TEMP. (Color temperature)
Adjusts the overall picture impression from warm to cool.
Four different types of color balance can be set beforehand:
LOW, MEDIUM, NORMAL and HIGH. Personal settings can
be made to set the resp. R,G and B levels.
To activate the personal setting, press the OK button on the
remote control when the color balance setting is selected.
With the cursor key (left/right) you can make your desired
personal setting;
– SOURCE CHANGE
For changing the possible input signal acceptance via the Data
input connector
- Data for standard PC signals
- YCbCr for component video signals (DVD)
VIEW
–
ASPECT
To set the aspect ratio. Four different settings can be selected
for images:
- REAL: input signal projection without pixel replacement;
- AUTO: projection after automatic input signal zoom-in / zoom-
out;
- DIRECT: the original aspect ratio of the image is maintained
at all times;
- 4:3 > 16:9: 4:3 aspect ratio images are projected after
conversion to the 16:9 aspect ratio.
– FILTER
To set the sharpness during pixel conversion (image
compression/enlargement);
– D-KEYSTONE
Corrects picture distortion of the vertical keystone type by
internal scaling;
- NORMAL: normal keystone correction
- FULL: in this mode, the image is
enlarged to fill the screen vertically
and then keystone correction is
performed.
– PAN
To move to the desired portion.
Input a signal that is rated SXGA (XGA for S-lite) to RGB/YCbCr
connector and then set the partial display position with
ASPECT set to Real.
Note: Less than the original size of the picture cannot be moved
because the whole image is fully displayed.
VIDEO/S-VIDEO MODE - NORMAL MENU
Press the Menu button with the flip cover of the remote control
closed, to display the normal menu, then use the cursor key
(up/down) to select the display and picture control functions. After
selection of the required function, set the required value setting
by means of the cursor key (left/right).
IMAGE (Picture control)
–
BRIGHTNESS
Adjusts brightness of the displayed picture;
– CONTRAST
Adjusts the overall contrast intensity;
– COLOR (Saturation)
Adjusts the color saturation of the projected image;
– TINT
Adjusts the tint of the projected image;
– SHARPNESS
Controls the contour impression of the picture.
Input source VIDEO/S-VIDEO COMPONENT VIDEO RGB
BRIGHTNESS
• • •
CONTRAST
• • •
COLOR • • -
TINT o - -
SHARPNESS • - -
Elements marked with ‘ • ‘ are adjustable.
The element marked with ‘ o ‘ is adjustable for NTSC and
NTSC4.43 only.
Elements marked with ‘-’ are not adjustable
8. Operation
19
Display and picture control