Panasonic KX-FG6550 - Manual (Page 85)

8. Programmable Features
83
k and l on the handset are not displayed
properly, the line mode selection is incorrect. Set
line mode to “
A”.
{ 1} “ A”
{ 2} “ B” (default)
Note:
L You can also program this feature with the
handset (feature 0531 or feature 0532 on
page 89).
{#}{ 6}{7} Setting the incoming message
monitor
To hear an incoming message (ICM) from the
speaker when the answering machine is
recording the message.
{
1} “ ON” (default): You can monitor the incoming
message.
{
2} “ OFF”: Deactivates this feature.
LINE 1:{#}{7}{2}{*} LINE 2:{#}{7}{2}{#}
Setting flash time
The flash time depends on your telephone
exchange or host PBX.
{
1} “ 90ms”
{ 2} “ 100ms”
{ 3} “ 110ms”
{ 4} “ 250ms”
{ 5} “ 300ms”
{ 6} “ 400ms”
{ 7} “ 600ms”
{ 8} “ 700ms” (default)
Note:
L The setting should stay at 700 ms unless
pressing {FLASH/CALL WAIT} fails to pick
up the Call Waiting call.
L If the unit is connected via a PBX, PBX
functions (transferring a call etc.) might not
work correctly. Consult your PBX supplier for
the correct setting.
L You can also program this feature with the
handset (feature 0521 and feature 0522 on
page 89).
{#}{ 7}{3} Setting the incoming call tone
This tone lets you know when a call is being
received on the other line, during a conversation
on the base unit.
{
1} “ OFF”: Deactivates this feature.
{ 2} “ 2” (default): The tone will sound 2 times.
{ 3} “ ON”: The tone will sound for as long as the
line rings.
Note:
L You can also program this feature with the
handset (feature 0*2 on page 90).
{#}{ 7}{4} Setting room monitor
{ 1} “ ON”
{ 2} “ OFF” (default)
See page 53 for details.
Note:
L You can also program this feature with the
handset (feature 0*3 on page 90).
{#}{ 7}{5} Setting the Caller ID number auto
edit feature
{
1} “ ON” (default)
{ 2} “ OFF”
See page 47 for details.
{#}{ 7}{6} Setting the connecting tone
If you often have trouble when sending faxes,
this feature allows you to hear connecting tones:
fax tone, ring back tone and busy tone. You can
use those tones to confirm the status of the other
party’s machine.
{
1} “ ON” (default): You will hear connecting
tones.
{
2} “ OFF”: Deactivates this feature.
Note:
L If the ring back tone continues, the other
party’s machine may not be a fax machine or
may have run out of paper. Check with the
other party.
L The connecting tone volume cannot be
adjusted.
LINE 1:{#}{7}{7}{*} LINE 2:{#}{7}{7}{#}
Changing the receiving mode in the AUTO
ANSWER setting
{
1} “ TAM/FAX” (default): Telephone Answering
Machine/Fax mode (page 59)
{
2} “ FAX ONLY”: Fax only mode (page 60)
{ 3} “ TAM ONLY”: Telephone Answering
Machine only mode (page 61)
Note:
L When the unit is set to TAM ONLY mode,
friendly reception (feature #46* and feature
#46# on page 82) will turn OFF automatically.
When you change the unit from TAM ONLY
mode to TAM/FAX mode or FAX ONLY mode,
friendly reception will be turned ON
automatically.
{#}{ 8}{0} Resetting advanced features to
their default settings
{
1} “ YES”
{ 2} “ NO” (default)
To reset the advanced features:
1. Press {MENU}.
2. Press {#}, then {8}{0}.
FG6550-PFQX2225ZA-en.book Page 83 Monday, August 8, 2005 8:16 PM