Kenwood KRF-V6200D - Manual (Page 20)

20
English
Speaker setup ("SP SETUP")
This sets up the speakers according to the speaker system in
use. Speaker setup is required every time the speaker system is
changed.
œ See (() and
select "SP SETUP".
∑ Use [MULTI CONTROL 5/∞] to select the subwoofer
setting.
Speaker Display Selection
Subwoofer
"SUBW ON" With Subwoofer
"SUBW OFF" Without Subwoofer
é Press [SETUP].
® Repeat steps ∑ – é for the rest of the speaker
setting.
Speaker Display Selection
Front speaker
"FRNT LRG" Large size front speaker
"FRNT NML" Average size front speaker
Center speaker
"CNTR NML" Average size center speaker
"CNTR LRG" Large size center speaker
"CNTR OFF" No center speaker is connected.
Surround speaker
"SURR NML" Average size surround speaker
"SURR LRG" Large size surround speaker
"SURR OFF" No surround speaker is connected.
Surround Back
speaker
"BS LRG" Large size surround back speaker
"BS NML" Average size surround back speaker
"BS OFF" No surround back speaker is connected.
"BS L/R"* 1
Left and Right Surround Back speakers are
connected.
"BS MONO"* 1
Only one Surround Back speaker is
connected.
Subwoofer re-
mix*
2
"RMX ON" Subwoofer re-mix is on.
"RMX OFF" Subwoofer re-mix is off.
* 1 This selection is available when either "BS LRG" or "BS NML" is
selected.
* 2 The function for adding the bass of other channels to the
subwoofer channel according to the speaker setup.
† Go to the next setting, "TEST TONE".
• If you wish to exit the setup mode, see
(.
Notes:
• When "SUBW OFF" is selected, the front speakers are
automatically set to "FRNT LRG".
• For "FRNT LRG" selection, no sound will be heard from subwoofer
even it is set to ON. However, if you select "RMX ON", you will be
able to hear sound from the subwoofer.
• When in STEREO mode, the sound goes directly to front speakers.
• If "FRNT NML" is selected, "CNTR LRG" cannot be selected.
• If "CNTR NML" or "CNTR OFF" is selected, "SURR LRG" cannot be
selected.
• If "SURR OFF" is selected, no surround back speaker can be
selected.
• "BS LRG" cannot be selected unless "SURR LRG" is selected.
• If "BS MONO" is selected, surround back signal can only be output
at the SURROUND BACK L terminal.
Adjusting the speaker level
("TEST TONE")
From your usual listening position, adjust the volume output of
each speaker. The output level from each speaker should be the
same.
œ See (() and
select "TEST TONE".
∑ Use [MULTI CONTROL 5/∞] to select either "AUTO"
or "MANUAL".
Display Selection
"AUTO"
The test tone is heard from the speakers one after another with
2 seconds each.
"MANUAL" The test tone is heard from the speaker you have selected.
é Press [SETUP].
® Adjust the output level.
If you select "AUTO":
When you hear the test tone from the speaker which
you wish to adjust, use [MULTI CONTROL
5/∞] and
adjust the volume of the test tone. When you finish
adjusting, press [SETUP].
If you select "MANUAL":
Use [MULTI CONTROL 5/∞] to adjust the volume of
the test tone and press [SETUP]. You will hear the
test tone from the next speaker.
† Go to the next setting, "DISTANCE".
• If you wish to exit the setup mode, see
(.
Speaker settings