Woodstock SHOP FOX W1829 - Manual (Page 24)

-22-
Df[\cN(/)0D]^%J`eZ\0&((
FG
<
I
8
K@FEJ
Jli]XZ\GcXe`e^
The purpose of surface planing on the jointer is to make
one flat face on a piece of stock (see
=`^li\j*'–*() to
prepare it for surface planing on a thickness planer.
Kfjli]XZ\gcXe\fek_\af`ek\i#[fk_\j\jk\gj1
(% Read and understand J8=, beginning onGX^\-.
)% Make sure your stock has been inspected for
dangerous conditions as described in the JkfZb
@ejg\Zk`feI\hl`i\d\ekjinstructions, on GX^\
)'%
*% Set the cutting depth for your operation. (We
suggest 1 ⁄
32
" for surface planing, using a more
shallow depth for hard wood species or for wide
stock.)
+% Make sure your fence is set to 90˚.
,% If your workpiece is cupped (warped), place it so
the concave side is face down on the surface of the
infeed table.
-% Start the jointer.
.% With a push block in each hand, press the workpiece
against the table and fence with firm pressure, and
feed the workpiece over the cutterhead (
=`^li\*').
Note: N_\epflic\X[`e^_Xe[n`k_glj_YcfZb ^\kj
n`k_`e+f]k_\Zlkk\i_\X[#c`]k`klgXe[fm\ik_\
Zlkk\i_\X[#Xe[gcXZ\k_\glj_YcfZbfek_\gfi$
k`fef]k_\nfibg`\Z\k_Xk`jfek_\flk]\\[kXYc\%
Efn#]fZljpfligi\jjli\fek_\flk]\\[\e[f]k_\
nfibg`\Z\n_`c\]\\[`e^#Xe[i\g\Xkk_\jXd\XZk`fe
n`k_pflikiX`c`e^_Xe[n_\e`k^\kjn`k_`e+f]k_\
Zlkk\i_\X[%Kfb\\gpfli_Xe[jjX]\#;FEFKc\k
k_\d^\kZcfj\ik_Xe+]ifdk_\Zlkk\i_\X[n_\e`k
`jdfm`e^
/% Repeat Jk\g. until the entire surface is flat.
=X`cli\ kf lj\ glj_ YcfZbj n_\e jli$
]XZ\gcXe`e^dXpi\jlck`eZlkk\i_\X[
ZfekXZk#n_`Z_n`ccZXlj\j\i`fljg\i$
jfeXc `ealip% 8cnXpj lj\ glj_ YcfZbj
kf gifk\Zk pfli _Xe[j n_\e jli]XZ\
gcXe`e^fek_\af`ek\i%
=`^li\*'% Typical surface planing
operation.
=`^li\*(%Illustration of surface planing
results.
Portion
Removed With
Jointer
@] pfl Xi\ efk \og\i`\eZ\[ n`k_ X af`ek\i# j\k
k_\ [\gk_ f] Zlk kf '# Xe[ giXZk`Z\ ]\\[`e^ k_\
nfibg`\Z\ XZifjj k_\ kXYc\j Xj [\jZi`Y\[ Y\cfn%
K_`j gifZ\[li\ n`cc Y\kk\i gi\gXi\ pfl ]fi k_\
XZklXcfg\iXk`fe%
EFK@:<