Continued), Synchro recording, Hlistening to sound from an external unit – Sharp MD-X8 User Manual
Page 47: Hsynchro recording
46
(Continued)
0dB
2
3
4
7
8
Synchro recording
W
-
-12
WWW
-4
WWWW
0
W
>
W
R
L
W
-
-12
WWW
-4
WWWW
0
W
>
W
A U X 1
T WWWWWWWWWWWWWWWW
W
-
WW
-12
WWW
-4
WWWW
0
W
>
W
R
L
M D
WWWW
1
WWWW
0 : 0 0
WWWWW Y
A U X 1
T WWWWWW
A . M A R K
W
O N
W
W
-
WW
-12
WWW
-4
WWWW
0
W
>
W
R
L
M D
WWWW
1
WWWW
0 : 0 0
WWWWW Y
A U X 1
T WWWWWW
A . M A R K
W
O N
W
W
-
WW
-12
WWW
-4
WWWW
0
W
>
W
R
L
M D
WWWW
1
WWWW
0 : 0 0
WWWWW Y
A U X 1
T WWWW
S O U N D
W
S Y N C R O
W
-
WW
-12
WWW
-4
WWWW
0
W
>
W
R
L
M D
WWWW
1
WWWW
0 : 0 2
WWWWW Y
A U X 1
T WWWW
S O U N D
W
S Y N C R O
H
H
H
H
H
Listening to sound from an external unit
To listen to digital sound
1
Press the AUX button so that the AUX OPT. or AUX COAX
display appears.
I
Each time the button is pressed, the display will change as follows:
AUX1
AUX2
AUX OPT.
AUX COAX
PHONO
2
Start playback on the external unit.
3
Adjust the sound level using the VOLUME control of this unit.
Note:
In the following cases, "DIN UNLOCK" appears and playback
sound is muted:
I
When the external digital unit is off.
I
When there is no digital input from the digital input jack.
To listen to analog sound
1
Press the AUX button so that the AUX 1 or AUX 2 display
appears.
I
When connecting an external unit to the "MD IN/AUX1 " terminal at the
front of the main unit, select "AUX1". When connecting to the "AUX2"
terminal at the rear of the main unit, select "AUX2".
2
Adjust the input sound level using the INPUT LEVEL control.
I
When the INPUT LEVEL control is turned counterclockwise, no sound
is obtained.
3
Start playback on the external unit.
4
Adjust the volume using the INPUT LEVEL control and VOL-
UME control on this unit.
H
H
H
H
H
Synchro recording
MD recording will start automatically as soon as playback is
started on the external unit. This applies to both digital inputs and
analog inputs.
I
The space-cut function will work automatically during synchro record-
ing.
I
Synchro recording is available only for recordings from an external
unit.
1
Load a recordable MiniDisc.
2
Press the AUX button to select the auxiliary input .
I
Select the input that corresponds to the terminals where the external
unit you want to record from is connected.
I
Each time the button is pressed, the display will change as follows:
AUX1
AUX2
AUX OPT.
AUX COAX
PHONO
To record analog signals, perform steps 3 - 8.
To record digital signals, perform steps 6 - 8.
3
Press the REC button, then start playback on the external unit.
4
Adjust the recording level using the INPUT LEVEL control.
I
The maximum level should not exceed 0 dB.
5
Stop playback on the external unit.
6
Press the MD
H
button.
7
Press the SYNCHRO REC button.
8
Start playback on the external unit.
I
Recording will start automatically.
I
To stop recording halfway, press the MD
H
button.
MD
MD
AUX
INPUT LEVEL
REC
AUX
REC
SYNCHRO
REC
VOLUME
DOWN
UP
38-58
98.6.23, 10:34 AM
46