JVC DT-V17L2D - Manual (Page 9)

8
q AC IN terminal
AC power input connector.
• Connect the provided AC power cord to an AC outlet.
• Attach the provided power cord holder to prevent
accidental disconnection of the AC power cord ( ☞ page
9).
w POWER switch
Turns the AC power on or off.
• You need to press
button on the front panel to turn
on the monitor after turning on the POWER switch.
e Screw holes for external battery attachment
Attach external battery for DC 12 V power supply by using
2 screw holes. Choose the appropriate screw holes from 1,
2, 3 or 4, according to the type of external battery.
• Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A)
external battery.
CAUTION
• Do not use the external battery for DC 24 V power supply.
• Use only the battery specified above. If a heavy battery is
used, it may fall off depending on the way the monitor is
used.
• When an external battery is attached, attach the ferrite core
(provided) to the power cord from the mount as illustrated
below.
* Using the audio level meter
You can check the conditions of the current EMBEDDED
AUDIO signals in the audio level meter. The setting for the
level meter is selected in “LEVEL METER SETTING” (
☞
“AUDIO SETTING” on page 11).
7 Rear panel
Daily Operations / Connections (cont.)
6 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the HD/SD SDI signals.
• The terminals accept also EMBEDDED AUDIO
signals including up to 12 audio channels with the
sampling frequency of 48 kHz.
7 E. AUDIO HD/SD SDI (SWITCHED OUT) terminal
(BNC)
Output terminal for the HD/SD SDI signals.
• The SDI signals of the current input (SDI 1 or SDI 2)
are re-clocked, then emitted.
• When the input other than SDI 1 and SDI 2 is
selected, the SDI signal of the input selected last
time is emitted from this terminal.
• The signals are emitted from this terminal only when
the monitor is on or in P.SAVE (power save) mode.
8 DVI-D (HDCP) terminal
Input terminal for the DVI-D signal.
• When the picture is not displayed correctly, change
the setting of “DVI INPUT SEL.” ( ☞ page 10).
• The DVI-D (HDCP) terminal on this monitor does
not conform to the HDMI standard.
9 DC IN 12V terminal
DC 12 V (maximum DC 17 V)
power input connector.
• While using both the AC and DC 12 V power
supply, AC power supply is preferentially used. If
the AC power supply is cut off (for example, when
unplugging the AC power cord), the power supply
automatically switches to the DC 12 V power supply.
p DC switch
Turns the DC 12 V power on or off.
• You need to press
button on the front panel to
turn on the monitor after turning on the DC switch.
• The monitor consumes the battery even while the
monitor is on standby. To save battery life, turn off
the DC switch.
Security slot
Install a security wire to this slot.
1 REMOTE terminal
Terminal for controlling the monitor by an external control.
☞ “External Control” on page 14
2 VIDEO terminals (BNC)
Input (IN) and output (OUT) terminals for the composite
signals.
3 COMPO. (Y, P B /B-Y, P R /R-Y) terminals (BNC)
Input (IN) and output (OUT) terminals for the analog
component (color difference) signals.
4 AUDIO (IN) terminals (pin jack)
Input terminals for the analog audio signals.
• Use this terminal for the analog audio connection of the
SDI.
5 AUDIO (MONITOR OUT) terminals (pin jack)
Output terminals for the analog audio signals.
• The terminals emit the audio signals through the AUDIO
(IN) terminal or EMBEDDED AUDIO signals through the
E. AUDIO HD/SD SDI input terminal.
• The signals are emitted from these terminals only when
the monitor is on or in P.SAVE (power save) mode.
• The EMBEDDED AUDIO signals are decoded into an
analog signals, then emitted.
• The EMBEDDED AUDIO signals are emitted only when
“SDI 1” or “SDI 2” is selected, and when EMBEDDED
AUDIO signals come in to the E. AUDIO HD/SD SDI
input terminal.
CAUTION
Do not connect the
power cord until all other
connections are completed.
Carry handle
Use this handle when carrying the monitor.
When using DC 12 V power (maximum DC 17 V),
check the DC IN 12V terminal pin signal, and use
the correct polarity. If the polarity is reversed, this
could cause a fire or personal injury.
Ferrite core
Ex.: When the Anton Bauer mount (QR DXC-M3A) is used
DT-V17L2D_EA_EN_R.indd 8 DT-V17L2D_EA_EN_R.indd 8 07.9.14 7:01:44 PM 07.9.14 7:01:44 PM