JVC DT-V17L2D - Manual (Page 13)

12 Menu Configuration—SET-UP MENU
FUNCTION SETTING
Setting for the sub menu display, color system, and color of the tally lamp
Item To do Setting value
sub menu POSI. Select the contents and displaying position of “sub menu.” ☞ “NOTE”
COLOR
SYSTEM Select the color system.
• If the picture is unstable with “AUTO,” select “PAL” or “NTSC.” AUTO, NTSC, PAL
TALLY SELECT Select the color of the tally lamp. GREEN, RED
PICTURE SUB ADJ.
Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.
Item To do Setting value
CONTRAST* 1 Adjust the standard level for the contrast adjusted
with CONTRAST knob on the front panel. –20 – +20
BRIGHT* 1 Adjust the standard level for the brightness
adjusted with BRIGHT knob on the front panel. –20 – +20
CHROMA* 1 Adjust the standard level for the chroma adjusted
with CHROMA knob on the front panel. –20 – +20
PHASE* 1 Adjust the standard level for the phase adjusted
with PHASE knob on the front panel. –20 – +20
NTSC SETUP Select the set-up level of the input NTSC signal. 00 (compliant with 0% set-up signal), 7.5 (compliant
with 7.5% set-up signal)
COMPO.
LEVEL Select the level of the analog component signal
(480i and 576i only). SMPTE (compliant with M2VTR signals), B75
(compliant with BetacamVTR 7.5% set-up signal),
B00 (compliant with BetacamVTR 0% set-up signal)
sub menu Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing the
actual picture.
reset Restore the default settings for all the items in “PICTURE SUB ADJ.”
SIZE/POSI. ADJ.
Adjusts the size and position of the picture.
Item To do Setting value
H SIZE* 2 Adjust the horizontal picture size.
Setting value varies depending on
the signals. H POSITION* 2 Adjust the horizontal picture position.
V SIZE* 2 Adjust the vertical picture size.
V POSITION* 2 Adjust the vertical picture position.
sub menu Display the sub menu which enables you to adjust the items of “SIZE/POSI. ADJ.” while viewing the
actual picture.
reset Restore the default settings for all the items in “SIZE/POSI. ADJ.”
WHITE BALANCE SET.
Selects the color temperature and adjusts the drive level and cutoff point of each color (R/G/B).
Item To do Setting value
COLOR TEMP. Select the color temperature. 6500K, USER, 9300K
R DRIVE, G DRIVE,
B DRIVE*
3
Adjust the drive level of each color (red, green, and
blue). MIN – 000 – MAX (in 256
grades)
R CUT OFF, G CUT
OFF, B CUT OFF*
3
Adjust the cutoff point of each color (red, green, and
blue). MIN – 000 – MAX (in 256
grades)
sub menu Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.”
while viewing the actual picture.
reset Restore the default settings for the drive levels and cutoff points of the selected color
temperature.
* 1 Memorized for each input.
* 2 Memorized for each signal format.
* 3 Memorized for each color temperature.
For the operation procedure, see page 7.
Operation guide
Shows the buttons for
each operation.
Setting of “sub menu POSI.”
The setting values and features are as follows.
LOWER1: Displays the current setting and adjustment bar at the
lower part of the screen.
UPPER1: Displays the current setting and adjustment bar at the
upper part of the screen.
LOWER2: Displays the current setting at the lower part of the screen.
UPPER2: Displays the current setting at the upper part of the screen.
• The adjustment bar is not displayed for some items.
• The menu automatically
disappears in about 30 seconds
after the previous operation.
• Some items may not appear on
the menu depending on the input
or the input signal.
• The items controlled by the MAKE
system do not appear on the
menu.
NOTE
DT-V17L2D_EA_EN_R.indd 12 DT-V17L2D_EA_EN_R.indd 12 07.9.14 7:01:48 PM 07.9.14 7:01:48 PM