Available signals, 7 available signals – JVC DT-V17L2D User Manual

Page 10

ENGLISH

7 Available signals

The following signals are available for this monitor.
Video signals

No.

Signal name

Signal format

shown in the

status display

(

☞ page 7)

Input terminal

VIDEO

COMPONENT

(Analog

component)

E. AUDIO HD/

SD SDI

(IN 1, IN 2)*

DVI-D (HDCP)

(Digital component/

digital RGB)

NTSC

√

—

PAL

√

—

B/W50

√

—

B/W60

√

—

480/59.94i

480/60i

—

√

—

576/50i

—

√

—

480/59.94p

480/60p

—

√

—

√

576/50p

—

√

—

√

640

∗480/59.94p 640∗480/60p

—

√

720/60p

—

√

720/59.94p

720/60p

—

√

720/50p

—

√

720/30p

—

√

—

720/29.97p

720/30p

—

√

—

720/25p

—

√

—

720/24p

—

√

—

720/23.98p

720/24p

—

√

—

1080/60i

—

√

1080/59.94i

1080/60i

—

√

1035/60i

—

√*

√

√*

1035/59.94i

1035/60i

—

√*

√

√*

1080/50i

—

√

1080/60p

—

√

1080/59.94p

1080/60p

—

√

1080/50p

—

√

1080/30p

—

√

1080/29.97p

1080/30p

—

√

1080/25p

—

√

1080/24p

—

√

1080/23.98p

1080/24p

—

√

1080/30psF

1080/60i

—

√*

—

1080/25psF

1080/50i

—

√*

—

1080/29.97psF

1080/60i

—

√*

—

1080/24psF

1080/24psf

—

√

—

1080/23.98psF

1080/24psf

—

√

—

√: Acceptable

—: Not acceptable

Compatible with EMBEDDED AUDIO signals

The signal is recognized as 1080/60i.

The signal is recognized as 1080/59.94i.

The signal is recognized as 1080/50i.

• Analog component signals are compatible with Y on sync signals.

Computer signals (preset)
DVI-D (HDCP) terminals

No.

Signal name

Resolution

Frequency

Scan system

Horizontal

Vertical

Horizontal (kHz)

Vertical (Hz)

VGA60

640

480 31.5

59.9

Non-interlace

WVGA60

852

480

31.5

59.9

Non-interlace

SVGA60

800

600

37.9

60.3

Non-interlace

XGA60

1024

768

48.4

60.0

Non-interlace

WXGA (1280)

1280

768

47.8

60.0

Non-interlace

WXGA+60

1440

900

55.9

60.0

Non-interlace

SXGA60*

1280

1024

64.0

60.0

Non-interlace

UXGA60*

1600

1200

75.0

60.0

Non-interlace

WUXGA60*

1920

1200

74.0

60.0

Non-interlace

720/60p

1280

720

45.0

59.9/60.0

Non-interlace

1080/60p*

1920

1080

67.5/67.4

59.9/60.0

Non-interlace

When signals of No. 7 – 9 and 11 come in, thin lines will become obscured because their signal resolution is higher

than the screen resolution (1440 x 900).

• Non-preset signals may not be displayed normally even if its frequency is within the acceptable range (

☞

“Horizontal/vertical frequency (computer signal)” on page 17).

• When a preset signal comes in, the signal format is shown on the status display. For other signals, the

resolution is shown.

Specification of the DVI-D (HDCP) terminal

Connect it to the DVI-D output terminal on a personal computer.

Note for connections

• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are completed.
• Refer also to the user manual of each piece of equipment.

Pin No. Input signal

T.M.D.S Data 2–

T.M.D.S Data 1–

T.M.D.S Data 0–

T.M.D.S Data 2+

T.M.D.S Data 1+

T.M.D.S Data 0+

T.M.D.S Data 2 shield

T.M.D.S Data 1 shield

T.M.D.S Data 0 shield

DDC Clock

+5 V Power

T.M.D.S Clock shield

DDC Data

GND

T.M.D.S Clock+

Hot Plug Detect

T.M.D.S Clock–

Attaching the power cord holder

• The provided power cord holder prevents accidental disconnection of

the AC power cord from the AC IN terminal.

• The power cord holder consists of two parts, a case and a cover.

CAUTION

• Use only the provided screws.
• Make sure the plug will not be pulled

out after the cover is attached to the
case.

AC IN terminal

Cover

Case

Tab

• To detach the cover, release

the tab.

DT-V17L2D_EA_EN_R.indd 9

07.9.14 7:01:45 PM