JVC DR-DX5SEK - Manual (Page 70)

Filename [DX5SEK_12Editing.fm]
Masterpage:Left0
70
EN
Page 70 Thursday, 10 November 2005 16:34
SYSTEM CONNECTIONS
Connect the satellite receiver to the [L-2 IN/DECODER] connector,
then connect the [L-1 IN/OUT] connector to the TV’s connector.
NOTES:
● Set AL-2 SELECTB to AVIDEOB or AS-VIDEOB. (A pg. 64)
● You can use the Automatic Satellite Programme Recording
function (A pg. 50) with this connection. (HDD deck only)
● To record a programme via the satellite receiver, select L-2 mode
by pressing PR +/– so that
AL-2B appears on the front display
panel.
● For details, refer to the instruction manual of the satellite receiver.
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
1
Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY
DIGITAL/PCM B. (A pg. 71)
● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.
(A pg. 71)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards
to its Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to
the speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely
affect the playback picture.
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and
ADIGITAL AUDIO OUTB is set to
ADOLBY DIGITAL/PCMB, it is not possible to switch the audio
channel of a bilingual programme recorded on a DVD-RAM or
DVD-RW (VR mode) disc. In this case, perform the following steps
using the remote control to switch
ADIGITAL AUDIO OUTB from
ADOLBY DIGITAL/PCMB to APCM ONLYB.
A Press SET UP to access the Main Menu screen.
B Press selection keys to select ADVD VIDEO SET UPB, then press G.
C Press selection keys to select AAUDIO OUTPUTB, then press G.
D Press selection keys to select ADIGITAL AUDIO OUTB, then
press ENTER.
E Press selection keys to select APCM ONLYB, then press
ENTER. (A pg. 71)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
Connecting To A Satellite Receiver
IMPORTANT
When you set
AL-2 SELECTB to ASAT VIDEOB or ASAT
S-VIDEO B (A pg. 64), it is possible to view a satellite broadcast
with the TV set to its AV mode even if the unit is turned off. When
the unit is in Stop mode or recording, press TV AV/VIDEO on the
remote control to turn off the VIDEO indicator on the front
display panel.
● If you turn on the unit when the satellite receiver’s power is off,
nothing appears on the TV screen. In this case, turn on the
satellite receiver, or set the TV to its TV mode, or press TV AV/
VIDEO on the remote control to set the unit to the AV mode.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
TV aerial cable
ANTENNA OUT
ANTENNA IN
TV
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
Dolby Digital Decoder or
amplifier with built-in DTS
Coaxial cable
(not supplied)
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
To [DIGITAL AUDIO
OUT (COAXIAL)]
To DIGITAL AUDIO input
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]
DX5SEK_00.book Page 70 Thursday, November 10, 2005 4:35 PM