Adjusting the bass sounds – JVC RX-F10S User Manual

Page 28

Sound adjustments

Selecting the subwoofer sound phase—SBWFR
PHASE

You can change the subwoofer sound phase to your preference.
• Once you have made an adjustment, it is memorized for each

source.

• You cannot use the remote control for this setting.

PHASE NORM.

Normally select this.

PHASE REV.

Select this when you feel the bass sound is
better with this mode rather than with “PHASE
NORM.”

Initial setting: PHASE NORM.

NOTE

This function takes effect only when “SUBWOOFER” is set to
“SUBWFR :YES” (see page 18).

Adjusting the equalization patterns—
D EQ 63Hz/250Hz/1kHz/4kHz/16kHz

You can adjust equalization patterns in five frequency bands
(center frequency: 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz) for the
front speakers.
• Once you have made an adjustment, it is memorized for each

source.

Adjustable range: –8 (dB) to +8 (dB) (in 2 dB intervals)

Initial setting: 0 (dB) for all bands

• When adjustment is made, the EQ indicator lights up on the

display.

If no adjustment is required, set all the frequency bands to
“0 (dB).”
• The EQ indicator goes off from the display.

From the remote control:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step

2 again.

Set the mode selector to “AUDIO/TV/VCR/STB.”

Press SOUND.

Press EQ FREQ repeatedly to
select the band you want to adjust.

Press EQ LEVEL +/– to adjust the
equalization pattern of the selected
band.

Repeat steps

2 and 3 to adjust

other bands.

NOTE

After pressing SOUND, the numeric
buttons work for sound adjustments. To
use the numeric buttons to operate your
target source, press the corresponding
source selecting button before operation;
otherwise, the remote control may not
work as you intend.

Adjusting the sound localization of the center
channel—CENTER GAIN

This setting is available only when Neo:6 Music is in use.
• If you have set “CENTER SPK” to “NO” (see page 18), the

center gain is not adjustable.

• Once you have made an adjustment, it is memorized until you

change the setting.

• You cannot use the remote control for this setting.

Adjustable range: 0 to 0.5 (in 0.1 step intervals)

Initial setting: C GAIN 0.2

As the number increases, the center channel will be localized
clearly.
Normally, select “0.2.”

Adjusting the bass sounds

Reinforcing the bass—BASS BOOST

You can boost the bass level—Bass Boost.
• Once you have made an adjustment, it is memorized for each

source.

B.BOOST ON

Select to boost the bass level.
The BASS indicator lights up on the display.

B.BOOST OFF

Select to deactivate the Bass Boost.

Initial setting: B.BOOST OFF

NOTE

This function affects only the sound coming out through the front
speakers.

From the remote control:

Set the mode selector to “AUDIO/TV/VCR/STB.”

Press SOUND, then press BASS
BOOST repeatedly.

• Each time you press BASS BOOST, the

Bass Boost turns on and off alternately.

NOTE

Attenuating the input signal—INPUT ATT

When the input level of analogue source is too high, the sound
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
• Once you have made an adjustment, it is memorized for each

source.

• You cannot use the remote control for this setting.

ATT ON

Select to attenuate the input signal level.
The ATT indicator lights up on the display.

ATT NORMAL

Select to deactivate attenuation.

Initial setting: ATT NORMAL

22-24RX-F10[B]_f.p65

04.2.13, 16:40