JVC RX-F10S - Manual (Page 19)

15
Basic operations
Turning off the sounds temporarily
From the remote control ONLY:
Press MUTING to turn off the sound through all
connected speakers and headphones connected.
“MUTING” appears on the display and the volume turns off.
To restore the sound, press MUTING again.
• Pressing VOLUME +/– (or turning MASTER VOLUME control
on the front panel) also restores the sound.
Changing the display brightness
You can dim the display—Dimmer.
From the remote control ONLY:
Press DIMMER repeatedly.
• Each time you press the button, the display brightness changes
as follows:
DIMMER 1: Dims the display slightly.
Dims the blue illumination slightly.
DIMMER 2: Dims the display more than DIMMER 1.
Dims the blue illumination slightly (same as
DIMMER 1).
DIMMER 3: Turns off the display and blue illumination.
(Temporarily canceled when you operate the
receiver.*)
DIMMER OFF: Cancels the Dimmer (normal display).
* Except when activating or deactivating TV Direct.
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
SLEEP indicator
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
10 20 30 40 50 60
90 OFF (canceled) 80 70
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS
L
LS SB RS
S . WFR LFE
C R L
LS SB RS
S . WFR LFE
C R
To cancel the Sleep Timer:
Press SLEEP repeatedly so that “SLEEP OFF” appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when:
– You turn off the receiver, or
– TV Direct is activated.
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analogue/digital input mode (see page 12)
• Speaker output level (see page 23)
• Subwoofer audio position (see page 14)
• Subwoofer phase (see page 24)
• Digital equalization pattern (see page 24)
• Bass boost (see page 24)
• Input attenuator mode (see page 24)
• Surround/DSP mode selection (see pages 34 and 35)
NOTE
If the source is FM or AM (MW), you can assign a different
setting for each band.
Signal and speaker indicators on the display
Signal indicators Speaker indicators
The signal indicators light up as follows:
L: • When digital input is selected: Lights up when the
left channel signal comes in.
• When analogue input is selected: Always lights up.
R: • When digital input is selected: Lights up when the
right channel signal comes in.
• When analogue input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LS*: Lights up when the left surround channel signal comes
in.
RS*: Lights up when the right surround channel signal comes
in.
SB: Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
* When monaural surround signal comes in, only “S” lights up.
NOTE
When “DVD MULTI” is selected as the source, all the signal
indicators except “SB” light up.
The speaker indicators light up as follows:
• The subwoofer indicator ( S . WFR ) lights up when
“SUBWOOFER” is set to “SUBWFR :YES.” For details, see
page 18.
• The other speaker indicators light up only when the
corresponding speaker is set to “SML (small)” or “LRG
(large),” and also when required for the current playback.
12-15RX-F10[B]_f.p65 04.2.13, 16:40 15