Uv10 tuner operation – Jensen Phase Linear UV10 User Manual
Page 15
11
UV10
TUNER OPERATION
Tuner TFT Display
1.
Current radio band indicator
2.
Radio frequency indicator
3.
Clock
4.
Stereo broadcasting indicator
5.
Strong Local signal broadcasting indicator
6.
Preset radio stations: Touch to recall preset stations
7.
Information about the current function
8.
EQ: Touch for quick access to Equalizer level settings
9.
: Touch to access the direct entry screen
10. Current preset station indicator
11.
|<<: Touch to seek backward
12. >>|: Touch to seek forward
13. <<: Touch to tune backward one step
14. >>: Touch to tune forward one step
15. BAND: Touch to change between AM/FM bands
16. 1/2: Touch to view a second screen of menu choices
17.
: Touch to view the SOURCE MENU and select a new
playback source
18. MEM: View screen used to enter current channel into
preset memory
19.
: Touch to view the SETUP menu
20. PS (Preview Scan): Touch to scan all stations available,
stopping for 5 seconds at each and continuing until a
station is selected
21. PTY Indicator
22. RDS Indicator
23. AS: Touch to automatically store stations
24. PTY: Touch to activate the PTY function
25. LOC: Press to activate/deactivate the Local function
Switching to Radio Tuner Source
•
Touch the top left corner of the screen (the RADIO
circle) to view the SOURCE MENU. Touch “Radio”.
•
Press the SRC button (10) on the front panel or remote
control (8) to switch to the AM/FM or RADIO source.
Selecting FM/AM Band
Touch the BAND button (15) on the screen, or press the ||>/
BAND
button on the remote control (30) to change between
the following bands: FM1, FM2, FM3, AM1, and AM2.
NOTE: The BAND button on the unit only works when the
TFT is closed.
Seek Tuning
To seek the next higher station:
•
Touch the >>| button on screen.
•
Press the >>| button (19) on the remote control.
To seek the next lower station:
•
Touch the |<< button on screen.
•
Press the |<< button (17) on the remote control.
Manual Tuning
To increase or decrease the tuning frequency one step:
•
Touch the >> or << buttons on screen.
•
Press the >> or << buttons (14, 22) on the remote
control.
Direct Tuning
To enter a radio station directly, touch the
button or press
the GOTO button (21) on the remote control to display the
direct entry menu.
Enter the desired radio station using the on-screen number
pad. Press the Enter button to tune to the selected station. To
exit the screen without changing the station, touch Exit. To
clear your entry and start over, touch Clear.
Using Preset Stations
Six numbered preset buttons store and recall stations for
each band. All six stored stations (P1-P6) for the current
band appear on the screen.
Storing a Station
1.
Select a band (if needed), then select a station.
2.
Touch the on-screen MEM button (18) to open the
preset screen.
3.
Touch the preset number in which you would like to
store the current station (or touch Exit to cancel and
close the menu). The preset number and station
appears highlighted.
Recalling a Station
1.
Select a band (if needed).
4
1
10 21
22
5
7
8
3
6
17
FM-1
P1
87.5 MHz
01:02 PM
E
Q
PS
PTY
BAND
AS
1/2
2/2
MEM
LOC
P1 87.5 MHz
P2 90.1 MHz
P3 98.1 MHz
P4 106.1MHz
P5 107.9MHz
P6 102.9MHz
PS:
ST
LOC
PTY
RDS
2
16
16
15
23
11
18
25
20
24
12
13
14
19
9
RADIO
FM: _ _ _ . _ MHz
1
2
3
4
5
6
7
8
9
0
Clear
Exit
Enter
Preset: _
E x i t
P1 P2
P3
P4 P5 P6