beautypg.com

Maintenance instructions, Spinning jets maintenance, Cleaning the bath – Jacuzzi FUZION BATH SERIES 7260 User Manual

Page 21: Repairs to the surface, Purging the whirlpool system, Bath additives

background image

ENGLISH

21

Jacuzzi Whirlpool Bath DE99000A 3/06

Spinning Jets Maintenance

(Models equipped with spinning jets)

If hair or other kind of debris gets caught in the bearings of

these jets, it could cause them to stop spinning. This may
require disassembly and cleaning. To do this, simply grab the
nozzle and pull straight out of the jet housing. The bearing
casing will be attached to the nozzle. These can be separated
by holding the casing and pushing the nozzle out from the rear
of the casing. After cleaning, reassemble in reverse.

Cleaning the Bath

To clean your bath, simply use a mild, nonabrasive liquid

detergent solution on the acrylic surfaces. To clean the wood
surfaces, follow the wood finish manufacturer's maintenance
and cleaning instructions.

You can protect and restore the gloss to a dulled acrylic

surface by applying Meguiar's #10 Mirror Glaze, a product
specifically designed for use on acrylic finishes. If Meguiar's
is not available, an acrylic polish of equal quality or automo-
tive paste wax is acceptable.

Never use abrasive household cleaners on any Jacuzzi

Whirlpool Bath product.

Repairs to the Surface

Minor scratches which do not penetrate the acrylic color

finish can be removed by lightly sanding with 600-grit wet/dry
sandpaper. Restore the gloss using Meguiar's Mirror Glaze
or automotive paste wax.

Major scratches and gouges which penetrate the acrylic

surface will require refinishing. Ask your Jacuzzi Whirlpool
Bath dealer for special instructions.

Minor scratches which do not penetrate the wood finish

can be repaired using the manufacturer's recommendations.

Major scratches and gouges which penetrate the wood

surface will require refinishing.

Purging the Whirlpool System

NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED
AT LEAST TWICE A MONTH

To remove accumulations of bath residue from the whirl-

pool system, it is recommended that a whirlpool bath be
purged at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each use
using our exclusive two-part plumbing system cleaner made
specifically for whirlpool baths. Systems Clean™ is available
through an authorized Jacuzzi Whirlpool Bath Distributor or by
calling us direct at 1-800-288-4002. Instructions for use:
Immediately after bathing and exiting the whirlpool bath, leave
the bath water in the tub and add hot water, if necessary, so the
water is at least 1" to 2" (25,4 mm to 50,8 mm) above the
highest jet. Turn on the unit without the aerator. Pour the
contents of the Systems Clean Packet 1 (taking care not to get
the material on yourself) into the bath near the intake for the
circulation pump. Repeat same process with Systems Clean
Packet 2. It is important to use Packet 1 before Packet 2
to avoid a strong odor.
Run the bath for 5 to 10 minutes.
Drain completely and rinse any residue.

If you have followed the standard purging instructions

above and still have an excess accumulation of bath residue
and desire an alternative cleaning mechanism, we recom-
mend SUPER SYSTEMS CLEAN PLUS manufactured by
Stearns Packaging to rectify this condition. This may be
obtained by contacting us at l-800-288-4002. It is recom-
mended that you follow the instructions provided by the
manufacturer with the product. Repeated use may be neces-
sary. SUPER SYSTEMS CLEAN PLUS does not replace the
necessity to regularly purge your whirlpool system with Sys-
tems Clean as recommended.

Bath Additives

NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.

If you want to use any kind of bath additive, use only a small

amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.

The use of certain bath oils, bubble baths and bath addi-

tives may increase the level of accumulations of bath residue
in the whirlpool system. If excess accumulations persist, you
should discontinue use of these products.

NOZZLE

BEARING CASING

PUSH FROM REAR
TO REMOVE
NOZZLE

MAINTENANCE INSTRUCTIONS