Recording set, Display set, Pg. 79) f – JVC DR-MV5SE User Manual
Page 79: Pg. 79), Pg. 79), “m, Ed on the disc
Masterpage:Right+
EN
79
Filename [MV5S_13Subsidiary.fm]
SUBSIDIARY SETTINGS
Page 79Wednesday, 31 August 2005 16:55
RECORDING SET
8 SAVE AS LIBRARY — OFF / ON
When this function is set to “ON”, the recording information is
automatically stored in the library. For details, refer to “Modify
Library Information” (
8 XP MODE REC AUDIO — DOLBY DIGITAL / LINEAR PCM
You can select the audio format when you record a title in XP
mode. When this function is set to “LINEAR PCM”, you can obtain
a high-quality audio sound.
DOLBY DIGITAL
: To record in Dolby Digital format.
LINEAR PCM
: To record in Linear PCM format.
8 AUDIO REC — NICAM 1/MAIN / NICAM 2/SUB / MONO
You can select the desired NICAM audio channel to be recorded
on a DVD-R/RW (Video mode) disc.
NICAM 1/MAIN
: To record the main language of NICAM audio.
NICAM 2/SUB
: To record the sub language of NICAM audio.
MONO
: To record the standard (monaural) sound of NICAM audio.
NOTE:
This function works only for the NICAM bilingual programme.
8 DIRECT REC — OFF / ON
When this function is set to “ON”, you can easily start recording the
programme that you are watching on your TV. Press and hold 7
and press 4 on the remote control, or press 7 on the unit.
NOTES:
● When you use the Direct Rec function, be sure to use a TV offering
T-V LINK, etc. and connect a fully-wired 21-pin SCART cable
between the unit and the TV. (
● If “DIRECT REC” is set to “OFF”, the 7 button functions as described
੬ pg. 26) or “Basic Recording (VHS)”
● During Direct Rec, “– –” appears on the front display panel.
● If a programme is recorded with the Direct Rec, the station name will
not be registered in the library. “– – – –” will be displayed for the
station name.
● Even if there is no power supply for more than 60 minutes, the unit
keeps the setting.
8 INPUT COLOUR SYSTEM — AUTO / PAL / SECAM
You can play back PAL discs, or record PAL and SECAM signals
on this unit. Select the appropriate colour system.
AUTO
: Normally select “AUTO”. “AUTO” identifies the input signal
and automatically switches to an appropriate colour system.
When “AUTO” is not selected, you have to switch the colour
system to an appropriate setting (PAL or SECAM) manually.
PAL
: To record PAL signals.
SECAM
: To record SECAM signals.
DISPLAY SET
8 SUPERIMPOSE — OFF / AUTO
When this function is set to “AUTO”, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (
OFF
: To turn off superimposed indications.
AUTO
: To superimpose operational indications for approximately
five seconds just after the corresponding operation.
NOTES:
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting.
● When you select “AUTO”, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 GREY/BLUE BACK — OFF / ON
When this function is set to “ON”, the TV screen becomes all grey
(DVD deck)/blue (VHS deck) when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
8 DIMMER — BRIGHT / DIMMED1 / DIMMED2 / OFF
You can change the brightness of the front display panel.
BRIGHT
: To turn on the light on the front display panel. (Blue lamp
on the front display panel is turned on.)
DIMMED1/DIMMED2
: To change the brightness level. (Blue lamp
on the front display panel is turned off.)
OFF
: To turn off the light on the front display panel. (Blue lamp on
the front display panel is turned off.)
8 POWER SAVE — OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
● During Power Save mode —
— the front display panel will be turned off.
— the Just Clock function (
pg. 88) does not work.
● Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer
Recording.
— “L-2 SELECT” is set to “DECODER” or “SAT VIDEO/RGB”. (
● It takes some time for the unit to complete initialisation after you turn
on the unit power, with “HELLO” blinking on the front display panel.
8 ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in 10
different languages. Though Auto Set Up selects the language
automatically (
੬ pg. 19), you can change the language setting
manually as required.
For details, refer to “On-screen Language Set (DVD Deck Only)”
(
MV5S_00.book Page 79 Wednesday, August 31, 2005 4:55 PM