JVC DR-MV5SE - Manual (Page 44)

Filename [MV5S_08Basic TimerDub.fm]
Masterpage:Left+
44
EN
EDITING
Page 44Wednesday, 31 August 2005 16:55
L-1 Output And L-1 Input Setting
The [L-1 IN/OUT] connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-1
OUTPUT” and “L-1 INPUT” to the appropriate mode depending on
the type of appliance connected to the unit’s [L-1 IN/OUT] connector.
1
Press SET UP to access the Main Menu screen.
2
Press w e to select “FUNCTION SET UP”, then press t.
3
Press w e to select “VIDEO
IN/OUT”, then press t.
4
Press rt to select “L-1
OUTPUT” or “L-1 INPUT”, then
press ENTER.
5
Press rt to select the
appropriate setting, then press
ENTER.
6
Press SET UP to complete the setting.
NOTES:
● If “L-1 INPUT” or “L-1 OUTPUT” is set to “S-VIDEO”, the
monochrome signal is output from VHS deck. Be sure to select
setting other than “S-VIDEO” when you use the VHS deck.
● When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (
੬ pg. 44)
● If “L-1 OUTPUT” is not set to “COMPONENT”, it is not possible to
output images from the [COMPONENT VIDEO OUT] connector.
* The boldface settings below indicate the settings at your purchase.
8 L-1 OUTPUT — SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
SCART VIDEO : If a connected appliance’s input is compatible only
with regular video signals, set to “SCART VIDEO”.
SCART S-VIDEO : If a connected appliance’s input is compatible
with Y/C signals, set to “SCART S-VIDEO”. You can obtain high-
quality picture. (For connection, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.)
SCART RGB : If a connected appliance’s input is compatible with
RGB signals, set to “SCART RGB”. You can obtain a high-quality
RGB picture.
COMPONENT : If a connected appliance’s input is compatible with
Y/P B /P R signals, set to “COMPONENT”. You can obtain a high-
quality Y/P B /P R picture. Switch the TV to the input that you can
watch component video pictures.
8 L-1 INPUT — VIDEO / S-VIDEO
VIDEO : If a connected appliance’s output is compatible only with
regular video signals, set to “VIDEO”.
S-VIDEO : If a connected appliance’s output is compatible with Y/C
signals, set to “S-VIDEO”. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, “SCART RGB” or
“COMPONENT”, it is not possible to set “L-1 INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is not possible to set “L-1
INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is only possible to set “L-1
OUTPUT” to “SCART VIDEO”.
● Component video signals are not output from the [L-1 IN/OUT]
connector.
● When Progressive scan mode is engaged, it is not possible to select
the setting of “L-1 OUTPUT”. (
੬ pg. 44)
Output/Input Set
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
ENTER
DVD
VHS
SET UP
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
EXIT
OK
SELECT
SET UP
DVD SET UP FUNCTION SET UP INITIAL SET UP
VIDEO IN/OUT RECORDING SET OTHERS
MONITOR TYPE
F-1 INPUT
L-1 INPUT
DISPLAY SET
L-1 OUTPUT
L-2 SELECT
VIDEO
VIDEO
SCART VIDEO
VIDEO/RGB
4:3LB
MV5S_00.book Page 44 Wednesday, August 31, 2005 4:55 PM