JVC 0303-MK-ID-SN - Manual (Page 47)

EN
47 TROUBLESHOOTING
An unusual mark appears.
¥ Check the section of the manual that explains LCD
monitor/viewfinder indications (
੬
pg. 54 – 57).
An error indication (E01, E02 or E06) appears.
• A malfunction of some kind has occurred. In this case
the camcorder’s functions become unusable.
¥ Remove the power supply (battery pack, etc.) and
wait a few minutes for the indication to clear. When
it does, you can resume using the camcorder. If the
indication remains even though you repeat the
above two or three times, please consult your
nearest JVC dealer. Do not eject the cassette. This
will cause damage to the tape.
An error indication (E03 or E04) appears.
• A malfunction of some kind has occurred. In this case
the camcorder’s functions become unusable.
¥ Eject the cassette once and re-insert it, then check if
the indication clears. When it does, you can resume
using the camcorder. If the indication remains even
though you repeat the above two or three times,
please consult your nearest JVC dealer.
The charger indicator on the camcorder does
not light.
• The temperature of the battery is extremely high/low.
• Charging is difficult in places subject to extremely
high/low temperatures.
¥ To protect the battery, it is recommended to charge
it in places with a temperature of 10 °C to 35°C
(
੬
pg. 48).
When the image is printed from the printer, a
black bar appears at the bottom of the screen.
• This is not a malfunction.
¥ By recording with “DIS” activated (
੬
pg. 33) this
can be avoided.
When the camcorder is connected via the DV
connector, the camcorder does not operate.
• The DV cable was plugged/unplugged with power
turned on.
¥ Turn the camcorder’s power off and on again, then
operate it.
The memory card cannot be removed from
the camcorder.
¥ Push in the memory card a few more times
(
੬
pg. 11).
Coloured bright spots appear all over the LCD
monitor or the viewfinder.
• The LCD monitor and the viewfinder are made with
high-precision technology. However, black spots or
bright spots of light (red, green or blue) may appear
constantly on the LCD monitor or the viewfinder.
These spots are not recorded on the tape. This is not
due to any defect of the unit. (Effective dots: more
than 99.99 %)
During recording, sound cannot be heard.
• This is normal.
Play, Rewind and Fast-Forward functions do
not work.
• The Power Switch @ is set to “ ” or “ ”.
¥ Set the Power Switch @ to “ ” (
੬
pg. 14).
A memory card cannot be played back.
• The Power Switch @ is set to “ ” or “ ”.
¥ Set the Power Switch @ to “ ” (
੬
pg. 18).
• The VIDEO/MEMORY Switch t is set to “VIDEO”.
¥ Set the VIDEO/MEMORY Switch t to “MEMORY”.
The LCD monitor image is distorted.
• During playback of the unrecorded portion,
High-speed Search and still playback, LCD monitor
indications appear distorted. This is not a defect.
Images on the LCD monitor are jittery.
• The speaker volume is too great.
¥ Turn the speaker volume down (
੬
pg. 14).
There is no playback picture on the
connected TV.
• Since the analogue input mode is engaged, the
camcorder is in the Record-Standby mode.
¥ Set “S/AV INPUT” to “OFF” in the Menu Screen
(
੬
pg. 35).
Blocks of noise appear during playback, or
there is no playback picture and the screen
becomes blue.
¥ Clean the video heads with an optional cleaning
cassette (
੬
pg. 49).
The LCD monitor, the viewfinder and the lens
have become dirty (ex. fingerprints).
¥ Wipe them gently with soft cloth. Wiping strongly
can cause damage (
੬
pg. 50).