JVC DLA-G150HTE - Manual (Page 35)

DLA-G150HTE
1-35
No.51847
65
ENGLISH
DEUTSH
FRAN
ÇAIS
ITALIANO
ESPAÑOL
Warning Messages
The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take
the corrective action described here.
Message Cause Corrective action Page
• No device is connected to the
input terminal.
• The terminal is connected but no
signal is output from the
connected device.
* The selected input mode (input
terminal) name is shown in the
first line of the massage.
• Connect a device to the selected
terminal.
• Operate the connected device
and output a signal.
9, 11,
24 ~ 29,
32
• The frequency of the input video
signal is out of range.
• The selected input mode (input
terminal) name is shown in the
first line of the message.
• Input the video signals whose
frequency is within the projector’s
specifications.
22, 23,
67
• Though the frequency of the input
video signal is within the
acceptable range, other items
such as resolution are out of the
projector’s specifications.
• The selected input mode (input
terminal) name is shown in the
first line of the message.
• Input the video signals that
satisfies the projector’s
specifications.
22, 23,
67
• When the FREEZE button is
pressed, this message appears
for a few seconds.
• When a button not acceptable is
pressed during freezing, this
message appears for a few
seconds to notify that the image is
being frozen.
• To release freezing, press the
FREEZE button on the remote
control.
12, 36
• When the FREEZE button is
pressed for the video signals that
cannot be frozen (UXGA, etc.),
this message appears for a few
seconds to notify that the image
cannot be frozen.
* To forcibly clear the message,
press the EXIT button.
• Freeze function does not work for
the inputted video signals.
To use this function, input the
video signals that can be frozen.
12, 36
P C 1
N o i m a g e s i g n a l i s i n p u t t e d .
P C 1
F r e q u e n c y o f i m a g e s i g n a l i s o u t o f r a n g e .
P C 1
N o i m a g e s i g n a l i s s h o w n f o r t h i s t y p e .
FREEZE
FREEZE
66
Warning Messages
Memo
The message display language corresponds to the menu display language setting. This is set to “English (English)” when the
projector is bought. The display language can be selected from 6 languages. (Refer to page 45.) However, the input mode
(PC1, PC2,Y/C, VIDEO) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English irrespective of the
display language setting.
The language settings in the section are explained in “English”.
• When the DIGITAL ZOOM button
is pressed for the video signals
that cannot be zoomed (UXGA,
etc.), this message appears for a
few seconds to notify that the
image cannot be digitally zoomed.
* To forcibly clear the message,
press the EXIT button.
• Digital-zoom function does not
work for the inputted video
signals.
To use the this function, input the
video signals that can be digitally
zoomed.
13, 36
• The accumulated lamp use time
reaches 900 hours.
* Every time the projector is turned
on, this message appears on the
screen.
• Press the EXIT button to clear the
massage.
(This display can be cleared with
the MENU button or other
buttons.)
• Arrange for a new light-source
lamp or replace the light-source
lamp a little earlier.
10, 12,
55 ,57
• The accumulated lamp use time
reaches 1000 hours.
The word “Warning” blinks.
* The message can be cleared by
pressing the EXIT button.
However, the same message will
appear every one hour.
* Once the projector is turned off,
the projector does not turn on
unless the light-source lamp is
replaced with new one.
* When the accumulated lamp use
time reaches 1010 hours, the
projector is forcibly shut off.
• Replace the light-source lamp
and reset the lamp use time.
57 ~ 60
Message Cause Corrective action Page
D.ZOOM
EXIT
Lamp replacement
EXIT
Warning
Lamp replacement