JVC DLA-M5000LU - Manual (Page 31)

31
Operating the Main Menu
ENGLI
S
H
DEUTSH
FRAN
Ç
AIS
ITALIANO
ESPA
Ñ
OL
DLA-M5000CLU (Re)/ LCT0978-001B / ENGLISH
Configuration of the Main Menu (Computer-related input)
Main menu (Computer-related inputs: During COMPUTER IN -1 or -2 input signal)
PIXEL CLOCK TRACKING: The lateral size and display area of video image are adjusted.
PHASE: Flickering or dim video image is adjusted.
POSITION V. POS.: The vertical position of the video image being projected is adjusted.
H. POS.: The horizontal position of the video image being projected is adjusted.
PICTURE BRIGHTNESS: The brightness of the video image being projected is adjusted.
CONTRAST: The contrast of the video image being projected is adjusted.
R-GAIN: The gain in red signal of the video image being projected is adjusted.
G-GAIN: The gain in green signal of the video image being projected is adjusted.
B-GAIN: The gain in blue signal of the video image being projected is adjusted.
TEXT MODE: Adjust easiness for reading text during RESIZE.
NORMAL: Normal
TEXT 1: Display the outline of small letters already.
TEXT 2: Makes the outline of large letters sharp.
ALL RESET: All the items adjusted are reset.
OPTIONS MENU AUTO OFF: Sets whether to turn off menu display automatically (YES) or not (NO).
LINE DISPLAY: Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds
after input switching.
RIGHT LEFT REV.: Image is reversed right-to-left.
TOP BOTTOM INV.: Image is inverted top-to-bottom.
CLAMP: Sets the clamp pulse’s position at the back porch (BP) or on the sink tip (ST). Normally,
the clamp pulse is used at BP. If, with some PCs or workstations, the screen becomes
unstable such as being too dark or too bright, try to switch to ST.
RESIZE: When the number of pixels (resolution) sought by the video image input is smaller than
that (resolution) of D-ILA device, the video image is then enlarged to a virtually full screen
size of D-ILA device and projected. (Resizing indication)
BACK COLOR: Specifies the background color when there is no image signal. Background color can be
selected from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.
COLOR TEMP.: Adjusts the color temperature of the video image being projected. Make adjustment when
the video image becomes reddish or bluish.
Color temperature can be set to LOW, MIDDLE, or HIGH.
ASPET CHANGE: Selects the vertical-to-horizontal ratio of the video image projected. The factory-set ratio
is 4 : 3. When projecting high-vision image, a ratio of 16 : 9 can be selected.
SLEEP TIME: Sets the length of sleep time. A set sleep time after input signal is depleted, the projector
goes into a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30
minutes, 60 minutes and 0 minute. (If you select 0 minutes, the sleep time will be
cleared.)
LAMP TIME: Indicates accumulated used hours of the light-source lamp.
SOURCE: Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or
the screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.
USER allows you to set a source which is uniquely adjusted by the user.
CHANNEL: Sets a line and multiple sources for each channel.
USER SOURCE SET
UP: Sets up an area for the source being input, and registers the user name.
DISPLAY SIZE: Adjusts H PIXEL, V PIXEL, H CENTER and V CENTER of video image.
DECODER: Does not work with computer-related inputs. (The color system is indicated in gray.)
LANGUAGE: Text on the screen can be changed to a language other than English. Languages that can be displayed are the
following six:
N N N N (Japanese), ENGLISH (English), DEUTSCH (German), ESPAÑOL (Spanish), ITALIANO
(Italian), and FRANÇAIS (French). However, some text such as “QUICK-ALIGNMENT” (Quick-Alignment), etc.
are shown only in English.
DLA-M5000LU&SCU Eng Re.book Page 31 Tuesday, March 12, 2002 3:56 PM