beautypg.com

JVC 1001MKV*UN*SN User Manual

Page 25

background image

25

Playback Zoom

To magnify the recorded image up to 10X at any
time during playback. Make sure that the TBC
mode is activated.

1) Press PLAY

T

to find the scene of interest.

2) Press ZOOM (T/W)

R

. Pressing T zooms in. To

end zoom press and hold W until magnification
returns to normal. Or, press STOP

U

and then

press PLAY

T

.

• Due to digital image processing, the quality of the

image may suffer.

Animation And Time-Lapse

The remote control lets you set/release interval
time and recording time without setting REC TIME/
INT. TIME (

pg. 21) in SYSTEM MENU.

Animation
Each time ANIM.

O

is pressed, the recording time

changes in the following order: 1/4S, 1/2S, 1S, 5S
and no indication (off).

Time-Lapse
Each time REC TIME

O

is pressed, the recording

time changes in the following order: 1/4S, 1/2S,
1S, 5S and no indication (off). Each time INT. TIME

f

is pressed, the interval time changes in the

following order: 15S, 30S, 1MIN, 5MIN and no
indication (off).

Insert Editing

You can record a new scene onto a previously
recorded tape. Only the video signal is recorded in
this mode.
1) Set the Power Switch

@

to “

”.

2) Play back the tape, locate the edit-out point and

press PAUSE

s

.

Press and hold COUNTER R/M

)

for more than 1 second to reset the tape

counter, then press it again for less than 1
second so that “M” appears.

3) Press REW

Y

to go a little beyond the beginning

of the scene you want to replace, press PLAY

T

to view the recorded tape, and press PAUSE

s

exactly at the edit-in point where the new scene
should start.

4) While holding down INSERT

I

, press and

release PAUSE

s

. w appears.

5) To begin Insert Editing, press START/STOP

P

.

When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode. To end Insert Editing,
press STOP

U

.

• During Insert Editing, the original audio will be

heard from the speaker.

• After step 4), “Retake” (

pg. 13) can be

performed.

• The tape may stop slightly before or after the

designated end point, and noise bars may appear.
Neither indicates a defect in the unit.

Audio Dubbing

You can record a new soundtrack on a prere-
corded tape (normal audio only). The sound is
recorded from the built-in microphone.

Perform steps 1) and 2) of the Insert Editing
procedure.

3) Press REW

Y

to go a little beyond the beginning

of the scene onto which you want to dub the new
audio, press PLAY

T

to view the recorded tape,

then press PAUSE

s

at exactly the point where

dubbing should start.

4) While holding down A. DUB

d

, press and

release PAUSE

s

.

5) To begin Audio Dubbing, press PLAY

T

. When

the counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode. To end Audio
Dubbing, press STOP

U

.

• Do not press REW

Y

or FF

a

during Audio Dub-

Standby, or the edit points will not be accurate.

• If the microphone is too close to the TV, or if the

TV’s volume is too high, whistling or howling may
occur.

For Insert Editing/Audio Dubbing
• Insert Editing and Audio Dubbing may not work

correctly if the tape contains blank segments, or if
the recording speed was changed during the
original recording.

• To edit/dub onto a tape, make sure the erase

protection tab is in the position that allows
recording.

• Do not press STOP

U

during Insert Editing or

Audio Dubbing, or the edit points will not be
accurate.