Integra DTR-8.8 - Manual (Page 95)

95
Recording
This section explains how to record the input source and
how to record audio and video from separate sources.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• Sources connected to the analog multichannel input
cannot be recorded.
• Various restrictions apply to digital recording. Refer to
the manuals supplied with your digital recording
equipment for more details.
• Digital input signals are output by only the digital out-
puts, and analog input signals are output by only the
analog outputs. There is no internal conversion from
digital to analog or vice versa.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
Audio sources can be recorded to a recorder (e.g., cas-
sette deck, CDR, MD) connected to the TAPE OUT or
DIGITAL OPTICAL OUT jacks. Video sources can be
recorded to a video recorder (e.g., VCR, DVR) con-
nected to the VCR/DVR OUT jacks. See pages 29 to 45
for hookup information.
Note:
• If you select a different input source during recording,
that input source will be recorded instead.
You can overdub audio onto your video recordings by
simultaneously recording audio and video from two sep-
arate sources. This is possible because only the audio
source is switched when an audio-only input source,
such as TAPE, TUNER, or CD, is selected, the video
source remains the same.
In the following example, audio from the CD player con-
nected to the CD IN and video from the camcorder con-
nected to the AUX 2 INPUT VIDEO jack are recorded
by the VCR connected to the VCR/DVR OUT jacks.
Recording the Input Source
1 Use the input selector buttons to
select the source that you want
to record.
See “Which Connections Should I
Use?” on page 30 to see which signals
can be output and recorded.
You can watch the source while record-
ing it. The AV receiver’s Master Vol-
ume control has no effect on recording.
2 On your recorder, start record-
ing.
3 On the source component, start
playback.
Remote
controller
+10
1 2 3
4 5 6
7 8 9
VCR/DVR CBL/SAT DVD
Tape Tuner CD
Phono
Game/TV AUX 1 AUX 2
0
Net/USB
Recording from Different AV Sources
1 Prepare the camcorder and CD player for
playback.
2 Prepare the VCR for recording.
3 Press the [AUX 2] input selector button.
4 Press the [CD] input selector button.
This selects the CD player as the audio source but
leaves the camcorder as the video source.
5 Start recording on the VCR, then start
playback on the camcorder and CD player.
Video from the camcorder and audio from the CD
player are recorded by the VCR.
RS232
DIGITAL COAXIAL
OPTICAL
REMOTE
CONTROL
IN 1
IN 1
IN 2
IN IN IN IN
PHONO
FRONT R
FRONT R (BTL)
SURR R CENTER SURR L SURR BACK R
CD TAPE AUX 1 GAME/TV
GAME/TV CBL/SAT
CBL/SAT
AUX 1 VCR/DVR
VCR/DVR DVD
DVD IR IN
GND
IN 2
IN 3
L L
V
V
S
S
R R
ASSIGNABLE
(DVD)
(CBL/SAT)
(VCR/DVR)
(GAME/TV)
(CD)
OUT
COMPONENT VIDEO ASSIGNABLE IN 3
Y
CB/PB
CR/PR
IN 2 IN 1(DVD) MONITOR OUT
OUT IN IN OUT IN IN FRONT CENTER
SUBWOOFER
SURR
MULTI CH
SURR BACK
MONITOR OUT
AM
ANTENNA
FM75
OUT
Bi-AMP
ZONE 2 OUT
HDMI
IN 1 IN 2 IN 3 IN 4
ASSIGNABLE
OUT MAIN OUT SUB
ZONE2 R
Camcorder
VCR CD player
video signal
audio signal