Integra DTR-8.8 - Manual (Page 130)

130
Zone 2 and Zone 3 —Continued
The 12V triggers A, B, and C can be used to turn on 12V
trigger-capable components automatically when they are
selected as the input source. The triggers can be set so
that they activate when a connected component is
selected as the input source for the main room, Zone 2,
Zone 3, or any combination of rooms.
When triggered, the output from a 12V TRIGGER OUT
goes high (+12 volts, 100 milliamperes max).
Hookup
• Use a miniplug cable to connect the AV receiver’s 12V
TRIGGER OUT A, B, or C jack to the 12 V trigger
input on a connected component.
When several components are turned on simultaneously
by using triggers A, B, and C, depending on the type of
components, a large amount of current may be drawn
momentarily. To prevent this, you can delay trigger sig-
nals A, B, and C individually. Another application for
trigger delay is eliminating the “thump” noise that’s
sometimes heard when a source component is turned on.
Delaying the trigger signal for your power amplifier so
that it’s the last component to be turned on will accom-
plish this.
Using the 12V Triggers
1 Press the [Receiver] Remote
Mode button, followed by the
[Setup] button.
The main menu appears onscreen.
2 Use the Up and Down [ ]/[ ]
buttons to select
“6. Miscellaneous,” and then
press [Enter].
The Miscellaneous menu appears.
FRONT L (BTL) FRONT R (BTL)
V
S
MONITOR OUT ZONE 2 OUT
RS232
DIGITAL COAXIAL
OPTICAL
REMOTE
CONTROL
IN 1
IN 1
IN 2 IN IN IN IN
PHONO
ZONE2 L FRONT R FRONT L SURR R CENTER SURR L SURR BACK R
CD TAPE AUX 1 GAME/TV
GAME/TV CBL/SAT
CBL/SAT
AUX 1 VCR/DVR
VCR/DVR DVD
DVD
GND
IN 2
IN 3
L L
R R
ASSIGNABLE (DVD)
(CBL/SAT)
(VCR/DVR)
(GAME/TV)
(CD)
OUT
OUT IN IN OUT IN IN FRONT FRONT CENTER
SUBWOOFER SUBWOOFER
CENTER SURR SURR
MULTI CH PRE OUT
SURR BACK SURR BACK
AC INLET
Bi-AMP SURR BACK L Bi-AMP
ETHERNET
HDMI
IN 1 IN 2 IN 3 IN 4 ASSIGNABLE OUT MAIN OUT SUB
ZONE2 R
AM ANTENNA FM75 COMPONENT VIDEO ASSIGNABLE IN 3
Y
CB/PB
CR/PR
IN 2 IN 1(DVD) MONITOR OUT 1 MONITOR OUT 2 /ZONE 2 OUT
V
S
ZONE 2 ZONE 3
PRE OUT
L
R
SW A B
IR
12V TRIGGER OUT
B
OUT
C
A B
12V TRIGGER OUT
C
Receiver
Setu
p
Enter
Enter
6.Miscellaneous
1.Volume Setup
2.OSD Setup
3.12V Trigger A Setup
4.12V Trigger B Setup
5.12V Trigger C Setup
3 Use the Up and Down [ ]/[ ]
buttons to select “12V Trigger A,
B, or C,” and then press [Enter].
The 12V Trigger A/B/C Setup screen
appears.
4 Use the Up and Down [ ]/[ ]
buttons to select “Delay,” and use
the Left and Right [
]/[ ] but-
tons to select: 0 sec, 1 sec, 2 sec,
or 3 sec.
When 0 sec is selected, the trigger sig-
nal is output as soon as the input source
is changed.
5 Use the Up and Down [ ]/[ ]
buttons to select an input source,
and use the Left and Right
[
]/[ ] buttons to select an
option.
Off: No trigger signal is output.
A 12-volt trigger signal is output when
the connected component is selected as
the source for:
Main: Main room.
Zone2: Zone 2.
Main/Z2: Main room or Zone 2.
Zone3: Zone 3.
Main/Z3: Main room or Zone 3.
Z2/Z3: Zone 2 or Zone 3.
Main/Z2/Z3: Main room, Zone 2, or
Zone 3.
6 When you’ve finished, press the
[Setup] button.
Setup closes.
Enter
Enter
6-x.12V Trigger x Setup
Delay 1sec
DVD Main/Zone2
VCR/DVR Main/Zone2
CBL/SAT Main/Zone2
TV/GAME Main/Zone2
AUX1 Main/Zone2
AUX2 Main/Zone2
TAPE Main/Zone2
TUNER Main/Zone2
CD Main/Zone2
PHONO Main/Zone2
NET/USB Main/Zone2
Enter
Enter
Enter
Enter
Setu
p