Interphase Tech 4538 - Manual (Page 84)

PowerQUICC II Hardware Configuration Word
62 Interphase Corporation
Example 2-1. PowerSpan Interrupt Map Registers Initialization Code
8‚svtˆ rQ†ƒhD‡r ˆƒ‡†Ã‰‚vq
”
SrtX v‡r"!ÃUfD@SГГГГГ‘0ГГI‚Гv‡r ˆƒ‡Ã†‚ˆ prÃrhiyrq
SrtX v‡r"!ÃUfD@S ГГГГГ‘0ГГI‚Гv‡r ˆƒ‡Ã†‚ˆ prÃrhiyrq
ÃHhƒÃD‡r ˆƒ‡Ã†‚ˆ pr†Ã‡‚ÃD‡r ˆƒ‡Ãƒv†ÃDIUDIU$Ãs‚ ÃDPȆhtrГГ
SrtX v‡r"!ÃUfD9SГГГГГГ‘$A0ÃÃD‡r ˆƒ‡Гqv )ГDIU$y’Ãh†Ãvƒˆ‡
SrtX v‡r"!ÃUfDHSfH7PYГ‘####0ГГH7PY"Г‡‚ГDIU6ÃH7PY#&Г‡‚ГDIU
SrtX v‡r"!ÃUfDHSf97ГГГ‘@86'%#!0ГГ97Г‡‚ГDIU6Ã97!)&Г‡‚ГDIU)$
SrtX v‡r"!ÃUfDHSf9H6ГГ‘##0ГГ9H6Y Г‡‚ГDIU6Ã9H6!"Г‡‚ГDIU
SrtX v‡r"!ÃUfDHSfCXГГГ‘!@86'%#0ГГI‚Г€hƒГs ‚€Г‚rГv‡ГƒvÃ‡‚ГhГ
‚‡ur
SrtX v‡r"!ÃUfDHSfQ ГГГ‘0ГГQ8DГ Гr ‚ †Г‚ГQ8DГ ГDIU6
SrtX v‡r"!ÃUfDHSfQ7ГГГ‘!!!!!!!!0ГГQ7Гr ‚ †Г‚ГDIU
SrtX v‡r"!ÃUfDHS!fQ7ГГ‘!!!0ГГQ7Гr ‚ †Г‚ГDIU
SrtX v‡r"!ÃUfDHSfHDT8Г‘!0ГГD!PГu‚†‡Г‡‚ГDIU6ÃD!PÃDPQǂÃ
DIU
SrtX v‡r"!ÃUfD@SГГГГГ‘ A0ÃÃDIU#ÃCXÃv‡r ˆƒ‡†Ãrhiyrq
–
PowerQUICC II Hardware Configuration Word
When the PowerQUICC II hardware reset signal is de-asserted, the PowerQUICC II
generates 64-bit reads into its boot memory (the FLASH) with addresses starting at 0 and
incremented by 8. The first eight bytes set its Hard Reset Configuration.
For the 4538, the PowerQUICC II Hard Reset Configuration is (must be):
• EARB = 0: Internal bus arbitration
• EXMC = 0: The internal memory controller is used
• CDIS = 0: The core is active
• EBM = 1: 60x-compatible bus mode
• BPS = 01: 8-bit boot port size
• –CIP = 0: Initial vector table base address is 0xFFF0 0000
• ISPS = 0: Responds as 64-bit slave to 64-bit masters
• L2CPC = 10: L2 cache pins configured as BADDR
• DPPC = 00: Data parity pins used for interrupt signals IRQ1 – 7
• ISB = 110: Internal Memory Mapped Register base address is
0xFF00 0000
• BMS = 0: Boot memory space is 0xFE00 0000
• BBD = 0: Bus Busy pins are enabled