beautypg.com

Configuring network protocol via the machine, Using the setip program, System requirements – Muratec Multi Functional Printer MFX-C2500 User Manual

Page 26: Windows, Macintosh, 26 system requirements

background image

26 _Getting started

Configuring network protocol via the machine

You can set up TCP/IP network parameters, follow the steps listed below.
1. Make sure your machine is connected to the network with an RJ-45

Ethernet cable.

2. Make sure you have turned on the machine.
3. Press Menu on the control panel, until you see Network on the bottom

line of the display.

4. Press OK to access the menu.
5. Press the left/right arrow until TCP/IP displays.
6. Press OK.
7. Press the left/right arrow until Static displays.
8. Press OK.
9. Press the left/right arrow until IP Address displays.
10. Press OK.

Enter a byte between 0 and 255 using the number keypad and press the

left/right arrow to move between bytes.

Repeat this to complete the address from the 1st byte to the 4th byte.

11. When you have finished, press OK.

Repeat steps 9 and 10 to configure the other TCP/IP parameters:

subnet mask and gateway address.

Using the SetIP program

This program is for the network IP setting using the MAC address which is

the hardware serial number of the network printer card or interface.

Especially, it is for the network administrator to set several network IPs at

the same time.

Installing the program

1. Insert the driver CD provided along with your machine. When the driver

CD runs automatically, close the window.

2. Start Windows Explorer and open the X drive. (X represents your CD-

ROM drive.)

3. Double click Application > SetIP.
4. Open the folder of the language you plan to use.
5. Double click Setup.exe to install this program.
6. Follow the instructions in the window and complete the installation.

Starting the program

1. From the Windows Start menu, select All Programs > Samsung

Network Printer Utilities > SetIP.

2. Select the name of your printer and click

.

3. Enter the network card's MAC address, IP address, subnet mask,

default gateway, and then click Apply.

4. Click OK to confirm the settings.
5. Click Exit to close the SetIP program.

SYSTEM REQUIREMENTS

Before you begin, ensure that your system meets the following

requirements:

Windows

Your machine supports the following Windows operating systems.

Macintosh

Contact the network administrator if you are not sure how to configure.

You can also set up the network settings through the network

administration programs.

SyncThru™ Web Admin Service: Web-based printer

management solution for network administrators. SyncThru™

Web Admin Service provides you with an efficient way of

managing network devices and lets you remotely monitor and

troubleshoot network machines from any site with corporate
internet access. Download this program from

http://

solution.samsungprinter.com

.

SyncThru™ Web Service: Web server embedded on your

network print server, which allows you to:

- Configure the network parameters necessary for the machine to

connect to various network environments.

- Customize machine settings.

SetIP: Utility program allowing you to select a network interface

and manually configure the IP addresses for use with the TCP/IP

protocol.

If you cannot find your printer name, click

to refresh the list.

If you do not know the network card's MAC address, print the

machine's network information report. (See "Printing reports" on

page 61.)

OPERATING

SYSTEM

REQUIREMENT (RECOMMENDED)

CPU

RAM

FREE HDD

SPACE

Windows 2000

Pentium II 400 MHz

(Pentium III 933 MHz)

64 MB

(128 MB)

600 MB

Windows XP

Pentium III 933 MHz

(Pentium IV 1 GHz)

128 MB

(256 MB)

1.5 GB

Windows 2003

Server

Pentium III 933 MHz

(Pentium IV 1 GHz)

128 MB

(512 MB)

1.25 GB to

2 GB

Windows Vista

Pentium IV 3 GHz

512 MB

(1024

MB)

15 GB

Internet Explorer 5.0 or higher is the minimum requirement for all

Windows operating systems.

Users who have an administrator right can install the software.

OPERATING

SYSTEM

REQUIREMENT (RECOMMENDED)

CPU

RAM

FREE HDD

SPACE

Mac OS X

10.3 ~ 10.4

Intel Processor

Power PC G4 /

G5

128 MB for a

Power-PC

based Mac (512

MB).

512 MB for an

Intel-based Mac

(1 GB)

1 GB

Mac OS X 10.5

Intel Processor

867 MHz or

faster Power

PC G4 /G5

512 MB (1 GB)

1 GB