FujiFilm FinePix A101 - Manual (Page 37)

(Lit red) (Flashing red)
73 72
iAn attempt was made to playback a
frame not recorded on this camera.
iThe SmartMedia contact area is
soiled.
iCamera fault.
iImages cannot be played back.
iWipe the contact surface on the SmartMedia
thoroughly with a soft, dry cloth. In some cases,
you may have to format the SmartMedia.
iContact your FUJIFILM dealer.
Warning Displays
eThe table below lists the warnings that are displayed on the LCD monitor
Warning Displayed Explanation Remedy
The batteries in the camera are fully
depleted or very low on charge.
There is no SmartMedia loaded, or
the SmartMedia loaded is a 5-volt
card.
iThe SmartMedia is not formatted.
iThe SmartMedia contact area is
soiled.
iCamera fault.
iThe SmartMedia contact area is
soiled.
iThe SmartMedia is damaged.
iThe SmartMedia format is incorrect.
iCamera fault.
The SmartMedia is fully recorded.
The SmartMedia is write-protected.
Replace the batteries or have new batteries
ready.
Load the SmartMedia (3.3V) in the correct
direction.
iWipe the contact area on the SmartMedia with
a soft dry cloth. It may be necessary to format
the SmartMedia. If the error message is still
displayed, replace the SmartMedia.
iContact your FUJIFILM dealer.
iWipe the contact area on the SmartMedia with
a soft dry cloth. It may be necessary to format
the SmartMedia. If the error message is still
displayed, replace the SmartMedia.
iContact your FUJIFILM dealer.
Use a SmartMedia that is not write-protected.
Erase some images or use a SmartMedia that
has ample free space.
Notes on the SmartMedia ™
h Do not use or store SmartMedia in very hot, humid or
corrosive environments.
h Take care not to touch the SmartMedia’s contact area
or allow the area to become soiled. Use a dry lint-free
cloth to wipe away any soiling that does occur.
h To avoid damage caused by static electricity, always
use the special static-free case provided during
transportation or storage, or keep the SmartMedia in
a storage case if available.
h Do not carry SmartMedia in locations such as a
trouser pocket. This could subject the SmartMedia to
excessive force when you sit down, thereby
damaging the SmartMedia.
h The SmartMedia may feel warm when it is removed
from the camera after extended periods of picture
taking or image viewing. This is normal and does not
indicate a fault.
h Inserting a SmartMedia that is charged with static
electricity into your camera may result in a camera
malfunction. If this occurs, switch the camera off and
then on again.
h Affix the label onto the designated area of the card.
Do not use third-party labels as this can lead to
problems when the card is inserted or removed.
h When you attach the label, take care that it does not
cover any of the write-protect area.
■Notes on Using SmartMedia with a PC
h If you intend to take photos using a SmartMedia that
has been used on a PC, format the SmartMedia on
your camera.
h When you format a SmartMedia in the camera and
then shoot and record images, a directory (folder) is
automatically created. Image data is then recorded in
this directory.
h Do not change or delete the directory (folder) names
or file names on the SmartMedia from your PC as this
will make it impossible to use the SmartMedia in your
camera.
h Always use the camera to erase image data on a
SmartMedia.
h To edit image data, copy the image data to the PC’s
hard disk and then edit the copied data.
■Specifications
Type Image memory card for digital cameras
(SmartMedia)
Operating voltage 3.3V
Conditions for use Temperature:
0°C to +40°C (+32°F to +104°F)
Humidity:
80% or less (no condensation)
Dimensions 37 mm × 45 mm × 0.76 mm
(1.45 in. × 1.77 in. × 0.03 in.) (W × H × D)