Havis-Shields Kwik-Kit KK-100-05 - Manual

KWIK KIT SPECIFICATIONS - MODEL KK-100-05
GENERAL DESCRIPTION:
It is the intention of this specification to describe a conversion kit capable of installation into a full size cargo van (non
extended) for use as a Law Enforcement Prisoner Transport vehicle. The insert provides seating for ten (10) persons and
shall have two (2) separate compartments which will allow the loading of prisoners into both the rear and side doors of the
van. The kit will be supplied with all Aluminum primary parts and will be capable of transfer into a new vehicle at a later
date. Driver side of rear bulkhead, wall and bench assemblies will have accommodations for OEM rear air conditioning
heat system. These accommodations will be included regardless if van has OEM rear air conditioning or not. All aluminum
parts on bulkheads, walls, ceilings, dividers and benches to a have a white powder coat finish.
FRONT BULKHEAD:
The driver compartment will be protected by a 63” wide X 50” high front bulkhead. It will be constructed from .125” thick
aluminum sheet metal. The sheet will be formed to provide a framework and will have additional channel welded in for
strength. The frame will have pre-punched holes to align with the wall and bench units. The entire assembly will be
attached to bench/walls using ¼" hardware. The upper section of bulkhead will include a .187 thick aluminum X 36”w X
30”h emergency exit hatch with two (2) heavy duty slide bolts. The hatch will have a perforated area for viewing that is
covered with .250” clear polycarbonate.
REAR BULKHEAD: (SINGLE REAR DOOR)
The rear OEM door will be protected by a 63” wide X 50” high bulkhead. It will be constructed from .125” thick aluminum
sheet metal. The sheet will be formed to provide a framework and will have additional channel welded in for strength. The
frame will have pre-punched holes to align with the wall and bench units. The entire assembly will be attached to the
bench/walls using ¼" hardware. This bulkhead will have one (1) rear inner security door measuring 30”wide X 46” high.
The door will be manufactured from .125” thick aluminum sheet metal. The sheet will be formed to provide a 2.125” thick
framework and will have additional channel welded in for strength. An exterior door skin will be attached using .187”
diameter aluminum rivets. The upper section of door must have a perforated area, which will allow officers to view into the
prisoner compartment. The door includes two (2) heavy-duty rotary slam latches. The latches will be activated by a single,
flush mounted, paddle handle that includes a key lock and two (2) keys. A secondary, tamperproof access will be provided
to override each latch assembly if necessary. The door will attach to the bulkhead frame using ¼” hardware and a stainless
steel continuous hinge.
SIDE COMPARTMENT: (SIDE ENTRY)
The side compartment will be separated from the rear compartment by the center divider wall. An additional side separator
partition will be attached to the divider and to the passenger side of the Kwik Kit. The separator partition will be
constructed the same as the front bulkhead. The separator must also include an emergency exit hatch (22” wide X 30”
high) with two (2) heavy-duty slide bolts. (Padlocks to be provided by end user if desired). The Emergency exit hatch will
also have a 16” wide X 13” high diamond shaped perforated area for viewing and ventilation. A single interior partition
with a 30” wide door will be mounted to separate the side compartment bench from the O.E.M. side doors. Framework and
door construction will be similar to the rear bulkhead, including dual rotary latches and paddle handle. The O.E.M. doors
will not have to be modified. This compartment is designed to minimize leg movement of detainee and provide additional
safety to officer.
BENCHES:
Benches will be constructed from .125” thick aluminum with rounded front edges and will include a four-inch (4”) wide X
full length, rubber “Non Slip” strip on bench tops. The driver side bench will seat five (5) people and will be 13” high X
13” deep X 97” long. The rear passenger side bench will seat three (3) people and will be 13” high X 13” deep X 58.5”
long. The bench for the side entry compartment will seat two (2) people and will be 13” high X 13” deep X 38.5” long.
This bench will mount against center divider facing passenger side of van and will also have an 11.5” X 31.5” cover plate
on front of bench. This plate is removable (at installation) to allow for the mounting of the optional under bench locking
storage door.
KK-100-05_SS_10-08