1. Push the catch to the left and remove the battery holder.
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.
3. Push the battery holder back into the remote control until you feel a click.
Remote Control Operation
Installation
Connecting the Projector
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press button on the control panel or the POWER button on the remote control to turn on the projector. The projector takes a minute or so to warm up.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
Powering Off the Projector:
1. Press button on the control panel or the POWER button on the remote control to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
2. Press button on the control panel or the POWER button on the remote control again to confirm.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
Adjusting the Projector
Adjusting the Projector Height
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image by sliding the zoom ring.
Adjusting Projection Image Size
Menu Operation
1. Press the MENU button to open the OSD menu.
2. When OSD is displayed, use p / q to select any feature in the main menu.
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
4. Use p / q to select the desired item and adjust the settings with t / u.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
Maintenance
Cleaning the Lens
Cleaning the Projector Housing
Cleaning the Filter Cover
1. Switch the projector off and unplug the AC power cord from the wall socket.
2. Remove the filter cover as the illustration shown.
3. Clean the filter cover.
4. Replace the filter cover.
5. Attach the filter cover.
6. Plug the power back into the projector.
Replacing the Lamp
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Setting” menu.
1. Push the catch to the left and remove the battery holder.
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.
3. Push the battery holder back into the remote control until you feel a click.
Remote Control Operation
Installation
Connecting the Projector
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press button on the control panel or the POWER button on the remote control to turn on the projector. The projector takes a minute or so to warm up.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
Powering Off the Projector:
1. Press button on the control panel or the POWER button on the remote control to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
2. Press button on the control panel or the POWER button on the remote control again to confirm.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
Adjusting the Projector
Adjusting the Projector Height
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image by sliding the zoom ring.
Adjusting Projection Image Size
Menu Operation
1. Press the MENU button to open the OSD menu.
2. When OSD is displayed, use p / q to select any feature in the main menu.
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
4. Use p / q to select the desired item and adjust the settings with t / u.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
Maintenance
Cleaning the Lens
Cleaning the Projector Housing
Cleaning the Filter Cover
1. Switch the projector off and unplug the AC power cord from the wall socket.
2. Remove the filter cover as the illustration shown.
3. Clean the filter cover.
4. Replace the filter cover.
5. Attach the filter cover.
6. Plug the power back into the projector.
Replacing the Lamp
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Setting” menu.
