Telex SS-1002 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for SS-1002 Telex
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 26 |
| Size: | 1.06 MB |
Show table of contents
Document Outline
- Model SS-1002 Single-Channel Intercom Speaker Station
- Models SS-2002 Two-Channel Intercom Speaker Station
- Model SS-2002 RM Two-Channel Rack Mount Intercom Speaker Station
- Technical Manual
- Introduction
- Description
- Features
- 1. Channel and Power Connections -
- 2. Configuration DIP Switches -
- 3. Panel Mic Key -
- 4. Speaker Key -
- 5. Channel Select Key (SS-2002 & SS-2002RM only) -
- 6. Volume Control -
- 7. Intercom Listen Key -
- 8. Call Key -
- 9. Intercom Talk Key -
- 10. Dynamic-Mic Headset Connector -
- 11. Panel Mic Connector -
- 12. Built-in Panel Microphone -
- 13. Sidetone Trimmers -
- 14. Balanced/Unbalanced Selector Switch -
- Configuration Pre-check
- DIP Switches
- Mic Kill Receive
- Call Signal Compatibility
- Incoming Call Beep
- Microphone Type
- Speaker Beep for Incoming Call
- Balanced/Unbalanced Switch
- Sidetone Trimmers
- Headset Connector Notes
- Panel Mic Connector Notes
- Intercom Channel Connections
- Description of Phantom-Powered Connection
- Description of Locally Powered Connection
- All Locally Powered Intercom Stations (Dry Lines)
- FIGURE 6. Intercom system using all locally powered U box stations.
- FIGURE 7. Audiocom mode line termination for dry-line operation. (One required for each channel). The termination is available via P/N 9020-7550-000.
- FIGURE 8. Audiocom mode connections for an SS-1002 Intercom Station in a U box. For Clear-Com connection, use the Unbalanced Mode Intercom Channel pin out information listed in “Specifications” on page 18.
- FIGURE 9. Audiocom mode connections for an SS-2002 Intercom Station in a U box. For Clear-Com connection, use the Unbalanced Mode Intercom Channel pin out information listed in “Specifications” on page 18.
- FIGURE 10. Audiocom cable wiring diagrams
- Power Up
- Sidetone Adjustment
- 1. Activate channel 1 as described in “Channel Select (SS-2002 & SS-2002RM Only)” on page 16.
- 2. Activate talk and listen as described in the operating instructions.
- 3. Slowly increase the volume to maximum while talking into the microphone.
- 4. Using a small, flat-head screwdriver, adjust the channel 1 sidetone trimmer to minimize your voice level in the headphones.
- 5. Activate channel 2.
- 6. Repeat the steps 1 through 5 to adjust the channel 2 sidetone.
- 7. Install the intercom station mounting screws after completing the adjustments. The stations is now ready for use.
- 1. Activate channel 1.
- 2. Activate talk and listen.
- 3. Set the volume control to the normal listening level for intercom audio.
- 4. While talking into the microphone, use a small, flat-head screwdriver to adjust the channel 1 sidetone trimmer so you can hear your own voice in the headphones at an acceptable level.
- 5. Activate channel 2.
- 6. Repeat the steps 1 - 5 to adjust the channel 2 sidetone.
- Channel Select (SS-2002 & SS-2002RM Only)
- Headset/Headphone/Speaker/Microphone Selection
- Receiving Calls
- Calling an Intercom Channel
- Specifications
- Dimensions
- Installing the Box to the Faceplate
- Notes