Makita BFR540 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for BFR540 Makita
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 12 |
| Size: | 470 KB |
Show table of contents
Document Outline
- ENGLISH
- SPECIFICATIONS
- Model
- BFR540
- BFR550
- BFR750
- Screw strip
- 4 x 25 - 55 mm
- 4 x 45 - 75 mm
- No load speed (min-1)
- 4,000
- Overall length
- 424 mm
- 464 mm
- Net weight
- 2.1 kg
- 2.3 kg
- 2.3 kg
- Rated voltage
- D.C. 14.4 V
- D.C. 18 V
- D.C. 18 V
- Standard battery cartridges
- BL1430
- BL1830
- • Due to our continuing programme of research and developmen
- • Note: Specifications may differ from country to country.
- END004-1
- Symbols
- The following show the symbols used for the equipment. Be su
- ･ Read instruction manual.
- ･ Only for EU countriesDo not dispose of electric equipment
- ENE033-1
- Intended useThe tool is intended for screw driving in wood,
- For Model BFR540
- ENG101-1
- For European countries onlyNoiseThe typical A-weighted noi
- Sound pressure level (LpA) : 77 dB(A)
- Uncertainty (K) : 3 dB(A)
- The noise level under working may exceed 85 dB (A).
- Wear ear protection.
- ENG204-1
- Vibration
- The vibration total value (tri-axial vector sum) determined
- Work mode: screwdriving without impact
- Vibration emission (ah) : 2.5 m/s2 or less
- For Model BFR550
- ENG101-1
- For European countries onlyNoiseThe typical A-weighted noi
- Sound pressure level (LpA) : 78 dB(A)
- Uncertainty (K) : 3 dB(A)
- The noise level under working may exceed 85 dB (A).
- Wear ear protection.
- ENG204-1
- Vibration
- The vibration total value (tri-axial vector sum) determined
- Work mode: screwdriving without impact
- Vibration emission (ah) : 2.5 m/s2 or less
- For Model BFR750
- ENG101-1
- For European countries onlyNoiseThe typical A-weighted noi
- Sound pressure level (LpA) : 76 dB(A)
- Uncertainty (K) : 3 dB(A)
- The noise level under working may exceed 85 dB (A).
- Wear ear protection.
- ENG204-1
- Vibration
- The vibration total value (tri-axial vector sum) determined
- Work mode: screwdriving without impact
- Vibration emission (ah) : 2.5 m/s2 or less
- ENH102-6
- EC-DECLARATION OF CONFORMITY
- Model; BFR540, BFR550, BFR750
- We declare under our sole responsibility that this product i
- EN60745, EN55014 in accordance with Council Directives, 2004
- CE2006
- 000230
- Tomoyasu Kato
- Director
- Responsible Manufacturer:Makita Corporation3-11-8, Sumiyos
- Authorized Representative in Europe:Makita International Eu
- GEA002-3
- GENERAL SAFETY RULES
- WARNING! Read all instructions. Failure to follow all instru
- SAVE THESE INSTRUCTIONS.
- Work area safety
- 1. Keep work area clean and well lit. Cluttered and dark are
- 2. Do not operate power tools in explosive atmospheres, such
- 3. Keep children and bystanders away while operating a power
- Electrical Safety
- 4. Power tool plugs must match the outlet. Never modify the
- 5. Avoid body contact with earthed or grounded surfaces such
- 6. Do not expose power tools to rain or wet conditions. Wate
- 7. Do not abuse the cord. Never use the cord for carrying, p
- 8. When operating a power tool outdoors, use an extension co
- Personal Safety
- 9. Stay alert, watch what you are doing and use common sense
- 10. Use safety equipment. Always wear eye protection. Safety
- 11. Avoid accidental starting. Ensure the switch is in the o
- 12. Remove any adjusting key or wrench before turning the po
- 13. Do not overreach. Keep proper footing and balance at all
- 14. Dress properly. Do not wear loose clothing or jewellery.
- 15. If devices are provided for the connection of dust extra
- Power tool use and care
- 16. Do not force the power tool. Use the correct power tool
- 17. Do not use the power tool if the switch does not turn it
- 18. Disconnect the plug from the power source and/or the bat
- 19. Store idle power tools out of the reach of children and
- 20. Maintain power tools. Check for misalignment or binding
- 21. Keep cutting tools sharp and clean. Properly maintained
- 22. Use the power tool, accessories and tool bits etc. in ac
- Battery tool use and care
- 23. Ensure the switch is in the off position before insertin
- 24. Recharge only with the charger specified by the manufact
- 25. Use power tools only with specifically designated batter
- 26. When battery pack is not in use, keep it away from other
- 27. Under abusive conditions, liquid may be ejected from the
- SERVICE
- 28. Have your power tool serviced by a qualified repair pers
- 29. Follow instruction for lubricating and changing accessor
- 30. Keep handles dry, clean and free from oil and grease.
- GEB017-1
- SPECIFIC SAFETY RULES
- DO NOT let comfort or familiarity with product (gained from
- 1. Hold power tools by insulated gripping surfaces when perf
- 2. Always be sure you have a firm footing.Be sure no one is
- 3. Hold the tool firmly.
- 4. Keep hands away from rotating parts.
- 5. Do not touch the bit or the workpiece immediately after o
- SAVE THESE INSTRUCTIONS.
- WARNING:
- MISUSE or failure to follow the safety rules stated in this
- ENC007-2
- IMPORTANT SAFETY INSTRUCTIONS
- FOR BATTERY CARTRIDGE
- 1. Before using battery cartridge, read all instructions and
- 2. Do not disassemble battery cartridge.
- 3. If operating time has become excessively shorter, stop op
- 4. If electrolyte gets into your eyes, rinse them out with c
- 5. Do not short the battery cartridge:
- (1) Do not touch the terminals with any conductive material.
- (2) Avoid storing battery cartridge in a container with othe
- (3) Do not expose battery cartridge to water or rain.A batt
- 6. Do not store the tool and battery cartridge in locations
- 7. Do not incinerate the battery cartridge even if it is sev
- 8. Be careful not to drop or strike battery.
- SAVE THESE INSTRUCTIONS.
- Tips for maintaining maximum battery life
- 1. Charge the battery cartridge before completely discharged
- 2. Never recharge a fully charged battery cartridge.Overcha
- 3. Charge the battery cartridge with room temperature at 10ﾟ
- FUNCTIONAL DESCRIPTION
- CAUTION:
- Always be sure that the tool is switched off and the battery
- Installing or removing battery cartridge
- 006801
- Always switch off the tool before insertion or removal of th
- To remove the battery cartridge, withdraw it from the tool w
- To insert the battery cartridge, align the tongue on the bat
- Do not use force when inserting the battery cartridge. If th
- Setting for desired screw length
- 008123
- There are 7 positive-lock screw length settings. To obtain t
- For Models BFR540, BFR550
- 008238
- For Model BFR750
- 008241
- Adjusting the driving depth
- 008124
- Depress the stopper base as far as it will go. While keeping
- Switch action
- 008282
- CAUTION:
- Before inserting the battery cartridge into the tool, always
- To start the tool, simply pull the switch trigger. Release t
- Reversing switch action
- 008283
- This tool has a reversing switch to change the direction of
- When the reversing switch lever is in the neutral position,
- CAUTION:
- Always check the direction of rotation before operation.
- Use the reversing switch only after the tool comes to a comp
- When not operating the tool, always set the reversing switch
- ASSEMBLY
- CAUTION:
- Always be sure that the tool is switched off and the battery
- Installing or removing the bit
- Loosen the thumb screws which secure the casing. Pull out th
- 008285
- Press the dust cover toward the plane bearing and pull out t
- 008286
- Installing screw strip
- Insert the screw strip through the screw guide. Then insert
- 008290
- 008288
- Removing screw strip
- To remove the screw strip, just pull it out in the direction
- 008281
- 008128
- Folding screw guide
- 008289
- Screw guide is foldable. Folding the screw guide allows spac
- Carry hook
- The carry hook is convenient for temporarily hooking the too
- 008262
- OPERATION
- Driving operation
- 008263
- Switch on the tool by pulling the switch trigger. Hold the t
- CAUTION:
- Always check the bit carefully for wear before driving opera
- Always hold the tool squarely against the driving surface. H
- Always keep the tool firmly against the driving surface unti
- Be careful not to drive a screw onto another screw already f
- Do not operate the tool without screws. It will damage the d
- Do not apply oil or grease on the sliding surface of the fee
- Driving in corner
- 006812
- This tool can be used to drive at a position 15 mm away from
- CAUTION:
- Driving at a position closer than 15 mm to the wall or driv
- MAINTENANCE
- CAUTION:
- Always be sure that the tool is switched off and the battery
- Replacing carbon brushes
- 006258
- Replace when they wear down to the limit mark. Keep the carb
- Loosen the thumb screws which secure the casing. Pull out th
- 008285
- Use a screwdriver to remove two screws then remove the front
- 008287
- Raise the arm part of the spring and then place it in the re
- 006816
- Use pliers to remove the carbon brush caps of the carbon bru
- 006817
- Make sure that the carbon brush caps have fit into the holes
- 006304
- Reinstall the front cover and tighten two screws securely.
- To maintain product SAFETY and RELIABILITY, repairs, any oth
- ACCESSORIES
- CAUTION:
- These accessories or attachments are recommended for use wit
- If you need any assistance for more details regarding these
- Drywall screw strip
- Phillips bit
- Various type of Makita genuine batteries and chargers
- Plastic carrying case