IBM SUREMARK TG4 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for SUREMARK TG4 IBM
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 244 |
| Size: | 3.09 MB |
Show table of contents
Document Outline
- Contents
- Figures
- Tables
- Preface
- Summary of changes
- GA27-4151-07 (April, 2009)
- GA27-4151-07 (February/March, 2007 update)
- GA27-4151-07 (May, 2006)
- Web-only update GA27-4151-06 (December, 2005)
- GA27-4151-06 (August, 2005)
- Web-only update for corrections to GA27-4151-05 (August, 2004)
- Web-only update for corrections to GA27-4151-05 (August, 2003)
- Web-only update for Model TI8, GA27-4151-05 (April, 2003)
- Web-only update for GA27-4151-04 (March, 2002)
- Web update for GA27-4151-04 (June, 2001)
- GA27-4151-04
- GA27-4151-03
- GA27-4151-02
- Part 1. General information
- Chapter 1. Introduction
- Chapter 2. Installation instructions
- Chapter 3. SureMark installation, service, and utility software
- Software adjustments (Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, and TG9)
- 4610 fonts and logos utilities
- Proportional font conversion utility
- Firmware update
- Using a firmware update diskette (Models TI1 and TI2 only)
- Using POSS for Windows to update SureMark printer firmware (RS-485 and USB only)
- Using JavaPOS for Windows to update SureMark printer firmware (EIA-232, RS-485, and USB)
- Updating SureMark firmware using temporary EIA-232 attachment
- Limitation on updating firmware
- Emulating the IBM Model 3 or Model 4 printers
- Emulating an Epson single-station printer (single-station only)
- MICR data parser sample code (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- Resources on the Internet
- Part 2. Models TI1, TI2, TI3, TI4, TI8, TI9, TG3, TG4, TG8, TG9
- Chapter 4. Operation
- Chapter 5. Testing and problem analysis
- Part 3. Models TF6 and TM6
- Chapter 6. Operation (Models TF6 and TM6)
- Chapter 7. Testing and problem analysis (Models TF6 and TM6)
- Part 4. Appendixes
- Appendix A. Consumable supplies
- Appendix B. Printer maintenance procedures
- Appendix C. Technical information
- Appendix D. EIA-232 programming information
- EIA-232 commands summary by function
- Alphabetized EIA-232 commands summary
- System commands
- Preset or Onetime-Set commands
- All models
- Models TI8 and TI9 only
- Download graphics (logo) commands
- Predefine messages
- Download user-defined characters
- Thermal code page
- Proportional font
- Impact code page
- Flash storage write
- Erase flash EPROM sector
- Send checksum of flash EPROM sector
- Microcode tolerance (MCT) information - loading
- Microcode tolerance (MCT) information - request
- Setup commands
- Set print mode
- Set or cancel double-wide mode
- Set or cancel double-high mode
- Set or cancel underline mode
- Set or cancel overline mode
- Set or cancel invert mode
- Set or cancel emphasized printing
- Select maximum print speed
- Set or cancel unidirectional printing
- Request document length for landscape print
- Set document length for landscape print
- Set print station
- Select user-defined or resident character sets
- Set code page
- Set intercharacter spacing
- Set or cancel rotated characters
- Set print station parameters
- Select 1/8-inch line spacing
- Select 1/6-inch line spacing
- Select color printing
- Set line spacing using minimum units
- Set sheet eject length
- Set horizontal tab positions
- Set left margin position
- Set relative position
- Align positions
- Set error recovery function
- Define document wait time
- Status sent to system
- Select character for reprinted lines
- Re-initialize the printer
- Enable or disable the feed buttons
- Enable or disable the beeper (Models TF6 and TM6 only)
- Enable or disable upside-down printing
- Select character size for scalable fonts
- Fix font matrix
- Print logo inline
- Select thermal paper
- Bar code commands
- Print bar code
- Select horizontal size of bar code
- Select bar code height
- Select printing position of human readable information (HRI)
- Select font for HRI
- Print PDF417 bar code
- Print PDF417 bar code using binary mode
- Select PDF417 ECC (error correction codewords) level
- Select aspect ratio PDF417 bar code
- Enable PDF417 truncation
- Print character commands
- Print graphic messages
- Miscellaneous commands
- Check processing commands (Models TI2, TI4, TI8, TI9, TG4, TG8, and TG9 only)
- Document scanner commands
- Asynchronous (real-time) commands
- Data buffer management and batch printing
- Page mode printing commands
- Select page mode
- Select standard mode
- Select printable area
- Select printing direction/position
- Set vertical position
- Set relative vertical position
- Set left margin position (standard mode), set absolute print position (page mode)
- Set relative horizontal position
- Set printing position
- Print and form feed and cut the paper
- Print page in page mode
- Clear print data in page mode
- Document handling
- Appendix E. Uploading electronic journal data
- Appendix F. Proportional fonts
- Appendix G. Emulation support for Epson single-station printer
- Appendix H. Safety information
- Appendix I. Notices
- Electronic emission notices
- Federal Communications Commission (FCC) statement
- European Union EMC Directive conformance statement
- Industry Canada Class A Emission Compliance statement
- Avis de conformité aux normes d'Industrie Canada
- Germany
- Australia and New Zealand
- Chinese Class A warning statement
- Japanese power line harmonics compliance statement
- Japanese Voluntary Control Council for Interference (VCCI) statement
- Korean communications statement
- Taiwanese Class A warning statement
- Taiwan contact information
- Cable ferrite requirement
- Electrostatic Discharge (ESD)
- Product Recycling and disposal
- Battery return program
- Flat panel displays
- Monitors and workstations
- Trademarks
- Electronic emission notices
- Index
- Readers’ Comments — We'd Like to Hear from You