HEIDENHAIN iTNC 530 (340 49x-04) Touch Probe Cycles Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for iTNC 530 (340 49x-04) Touch Probe Cycles HEIDENHAIN
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 191 |
| Size: | 7.19 MB |
Show table of contents
Document Outline
- TNC Model, Software and Features
- Functions changed since the predecessor versions 340 422-xx/ 340 423-xx
- Working with Touch Probe Cycles
- 1.1 General Information on Touch Probe Cycles
- 1.2 Before You Start Working with Touch Probe Cycles
- Maximum traverse to touch point: MP6130
- Safety clearance to touch point: MP6140
- Orient the infrared touch probe to the programmed probe direction: MP6165
- Consider a basic rotation in the Manual Operation mode: MP6166
- Multiple measurement: MP6170
- Confidence interval for multiple measurement: MP6171
- Touch trigger probe, probing feed rate: MP6120
- Touch trigger probe, rapid traverse for positioning: MP6150
- Touch trigger probe, rapid traverse for positioning: MP6151
- KinematicsOpt: Tolerance limit in Optimization mode: MP6600
- KinematicsOpt, permissible deviation of the calibration ball radius: MP6601
- Running touch probe cycles
- Touch probe cycles in the Manual and Electronic Handwheel modes
- Touch Probe Cycles for Automatic Workpiece Inspection
- 3.1 Measuring Workpiece Misalignment
- Overview
- Characteristics common to all touch probe cycles for measuring workpiece misalignment
- BASIC ROTATION (touch probe cycle 400, DIN/ISO: G400)
- BASIC ROTATION from two holes (touch probe cycle 401, DIN/ISO: G401)
- BASIC ROTATION over two studs (touch probe cycle 402, DIN/ISO: G402)
- BASIC ROTATION compensation via rotary axis (touch probe cycles 403, DIN/ISO: G403)
- Setting a BASIC ROTATION (touch probe cycle 404, DIN/ISO: G404)
- Compensating workpiece misalignment by rotating the C axis (touch probe cycle 405, DIN/ISO: G405)
- 3.2 Presetting automatically
- Overview
- Characteristics common to all touch probe cycles for datum setting
- Measurement results in Q parameters
- SLOT CENTER REFERENCE POINT (touch probe cycle 408, DIN/ISO: G408, FCL 3 function)
- SLOT CENTER REFERENCE POINT (touch probe cycle 409, DIN/ISO: G409, FCL 3 function)
- DATUM FROM INSIDE OF RECTANGLE (touch probe cycle 410, DIN/ISO: G410)
- DATUM FROM OUTSIDE OF RECTANGLE (touch probe cycle 411, DIN/ISO: G411)
- DATUM FROM INSIDE OF CIRCLE (touch probe cycle 412, DIN/ISO: G412)
- DATUM FROM OUTSIDE OF CIRCLE (touch probe cycle 413, DIN/ISO: G413)
- DATUM FROM OUTSIDE OF CORNER (touch probe cycle 414, DIN/ISO: G414)
- DATUM FROM INSIDE OF CORNER (touch probe cycle 415, DIN/ISO: G415)
- DATUM CIRCLE CENTER (touch probe cycle 416, DIN/ISO: G416)
- DATUM IN TOUCH PROBE AXIS (touch probe cycle 417, DIN/ISO: G417)
- Datum at center of 4 holes (touch probe cycle 418, DIN/ISO: G418)
- DATUM IN ONE AXIS (touch probe cycle 419, DIN/ISO: G419)
- 3.3 Automatic Workpiece Measurement
- Overview
- Recording the results of measurement
- Measurement results in Q parameters
- Classification of results
- Tolerance monitoring
- Tool monitoring
- Reference system for measurement results
- REFERENCE PLANE (touch probe cycle 0, DIN/ISO: G55)
- DATUM PLANE (touch probe cycle 1)
- MEASURE ANGLE (touch probe cycle 420, DIN/ISO: G420)
- MEASURE HOLE (touch probe cycle 421, DIN/ISO: G421)
- MEAS. CIRCLE OUTSIDE (touch probe cycle 422, DIN/ISO: G422)
- MEAS. RECTAN. INSIDE (touch probe cycle 423, DIN/ISO: G423)
- MEASURE RECTANGLE FROM OUTSIDE (touch probe cycle 424, ISO: G424)
- MEASURE INSIDE WIDTH (touch probe cycle 425, DIN/ISO: G425)
- MEASURE RIDGE WIDTH (touch probe cycle 426, DIN/ISO: G426)
- MEASURE COORDINATE (touch probe cycle 427, DIN/ISO: G427)
- MEAS. BOLT HOLE CIRC (touch probe cycle 430, DIN/ISO: G430)
- MEASURE PLANE (touch probe cycle 431, DIN/ISO: G431)
- 3.4 Special Cycles
- 3.1 Measuring Workpiece Misalignment
- Touch Probe Cycles for Automatic Kinematic Measurement
- Touch Probe Cycles for Automatic Tool Measurement
- 5.1 Tool Measurement with the TT Tool Touch Probe
- 5.2 Available Cycles
- Overview
- Differences between Cycles 31 to 33 and Cycles 481 to 483
- Calibrating the TT (touch probe cycle 30 or 480, DIN/ISO: G480)
- Measuring the tool length (touch probe cycle 31 or 481, DIN/ISO: G481)
- Measuring the tool radius (touch probe cycle 32 or 482, ISO: G482)
- Measuring the tool radius (touch probe cycle 33 or 483, ISO: G483)
- Overview