Bosch WAP24200UC Instruction Manuals and User Guides
We have 4 Instruction Manuals and User Guides for WAP24200UC Bosch
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 3 |
| Size: | 656 KB |
| Recognized languages: | English |
|---|---|
| Pages: | 36 |
| Size: | 4.80 MB |
Show table of contents
Document Outline
- en-us Use and care manual
- Table of contentsen-us Use and care manual
- Important information
- Customer service
- IMPORTANT SAFETY INSTRUCTIONS
- IMPORTANT SAFETY INSTRUCTIONS
- READ AND SAVE THESE INSTRUCTIONS
- Introduction to your new washer
- Special features
- Environmentally friendly use of your washer
- Length of power cord and water supply hoses
- Installation types
- Introduction
- Tools needed
- Waste disposal
- Parts provided with your washer
- Set up on a pedestal with drawer
- Installation checklist
- Importance of installing on a solid, level floor
- Remove the transport bolts
- 9 CAUTION
- 1. Remove hoses from the brackets.
- 2. Loosen and remove all 4 transport bolts. Remove the sleeves. Take the power cable out of the brackets.
- 3. Place covers over the transport bolt holes Four plastic covers are provided in the small parts bag included with your washer. Separate these covers and install one in each hole where the transport bolts were removed. Lock covers firmly by pressing...
- NOTICE:
- Water connections
- Leveling the washer
- 2. If the floor is uneven (or unlevel) adjust the washer feet as required to level the washer. Do not place anything under the washer feet to help level the washer.
- 3. Extend the washer feet no more than is necessary. The more the feet are extended, the more vibration the washer will experience. Start with the washer feet turned all the way in and adjust each foot as necessary.
- 4. Use a bubble level to check the top of the washer to make sure it is level side to side and front to rear.
- 5. Press down on each corner of the washer top to make sure the washer doesn’t “wobble“. There should be no "give" or movement. All four washer feet should press equally against the floor. This is just as important as the washer being level to ...
- 6. When the washer is level and does not wobble, lock the washer feet in place by tightening the locknuts against the washer bottom. Be sure to do this without changing the height of the foot (hold the foot while tightening the locknut).
- 1. After determining which washer feet need to be extended, have someone lift up on the washer slightly to take pressure off the foot to be adjusted.
- 2. Turn the grey plastic foot to extend it downward as far as necessary to raise the corner of the washer the correct amount to level the washer.
- 2. Turn off the water supply to the washer.
- 3. Disconnect water supply lines from the tap.
- 4. Disconnect the drain hose from the drain location.
- 2. Pull the tip of the arrow on the cover out slightly to disengage the locking tab.
- 2. Insert the transportation bolt and bushing assembly as shown. The metal housing slides around the bolt through the slot in the plastic bushing as the bushing is slid into place. The open part of the bushing slot should be facing the direction show...
- 3. When the bolt is in place screw it in until the bolt threads engage the drum. Double check and ensure bolts are screwed into threaded holes and not into adjecent cracks or crevices. Repeat the process for all 4 transportation bolt assemblies befor...
- Getting to know your appliance
- Display field
- Sorting the Laundry
- Identifying and treating stains
- Starching
- Dyeing/bleaching
- Soaking
- 2. Turn the program selector to Cotton Normal Cold program.
- 3. Press Start/Pause.
- 4. After approx. ten minutes, press Start/Pause.
- 2. Press the Delay Start button until the desired number of hours is displayed.
- 3. Press the Start/Pause button
- NOTICE:
- Additional program settings
- Easy Iron
- Prewash/Pre Treat
- Before loading your first load of laundry
- Using the cycle selector to choose a wash cycle
- Changing default cycle settings
- Selecting additional cycle settings
- Loading the laundry
- Filling the detergent and additives compartments
- 2. Add detergent or additive.
- 3. Avoid overfilling the compartment to prevent early dispensing.
- 2. Push the liquid detergent dispenser forward.
- 2. Select another cycle.
- 2. Cool the laundry off: Select Rinse.
- 2. Select Spin/Drain.
- 2. Turn the cycle selector to the Off position. Appliance is switched off.
- 3. Turn off the water tap.
- 2. Remove the liquid detergent insert (3) by grasping it and pulling it upwards from the detergent dispenser drawer.
- 3. Clean the insert by holding it under warm running water. Lightly wipe away any remaining detergent residue.
- 2. Turn the cycle selector to any wash cycle (not to Drain or Spin).
- 3. Press Start/Pause and allow 30 seconds to pass.
- 2. Rinse the strainer under running water. Look at the strainer to see if any visible debris is still present. Rinse again if necessary to remove the debris.
- 2. Using narrow pliers, grasp and pull the strainer from the inlet port.
- 3. Rinse the strainer under running water.
- 4. Reconnect the hose to the back of the washer and turn on the water tap. Check to see if water flows by starting a warm water wash cycle.
- NOTICE:
- Cleaning the drain pump
- 3. Open and remove the service cover.
- 4. Loosen the screws and remove the protective film.
- 5. Use the pull-out drain hose located in the pump access opening to drain the remaining water into a suitable container (up to 5.3 U.S. gallons/20 liters of water may be drained). Pull the sealing cap from the hose and lay the hose over the side of ...
- 6. Turn the pump cover counterclockwise to remove it. A small amount of residual water may flow out when the cover is removed. Clean the interior of the pump housing, removing any debris or foreign objects. Check to be sure the impeller wheel at the ...
- 7. Screw the protective film on the pump on again.
- 2. Allow the water in the drum to cool off.
- 3. Allow the washer drum to come to a stand still (no longer spinning).
- 5. Loosen screws and remove the protective foil.
- 2. Disconnect the washer from the power outlet.
- 3. Turn off the water faucet.
| Recognized languages: | English |
|---|---|
| Pages: | 16 |
| Size: | 1.32 MB |
| Recognized languages: | English |
|---|---|
| Pages: | 1 |
| Size: | 10 KB |