Artesyn ATCA-9305 User's Manual (May 2014) Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for ATCA-9305 User's Manual (May 2014) Artesyn
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 270 |
| Size: | 17.05 MB |
Show table of contents
Document Outline
- ATCA-9305
- Regulatory Agency Warnings & Notices
- Contents
- Safety Notes
- Sicherheitshinweise
- About this Manual
- Overview
- Setup
- Cavium Processor Complex
- Management Complex
- Management Processor CPLD
- 5.1 MPC8548 PLD Register Summary
- 5.1.1 Product ID
- 5.1.2 Hardware Version
- 5.1.3 PLD Version
- 5.1.4 PLL Reset Configuration
- 5.1.5 Hardware Configuration 0
- 5.1.6 Jumper Settings
- 5.1.7 LED
- 5.1.8 Reset Event
- 5.1.9 Reset Command 1
- 5.1.10 Reset Command 2
- 5.1.11 Reset Command 3
- 5.1.12 Reset Command 4
- 5.1.13 Reset Command 5
- 5.1.14 Reset Command Sticky #1
- 5.1.15 Reset Command Sticky #2
- 5.1.16 Boot Device Redirection
- 5.1.17 Miscellaneous Control
- 5.1.18 Low Frequency Timer 1 and 2
- 5.1.19 RTM GPIO State
- 5.1.20 RTM GPIO Control
- 5.1.21 RTM Status
- 5.1.22 Cavium 1 C_MUL Clock Divisor Control
- 5.1.23 Cavium 2 C_MUL Clock Divisor Control
- 5.1.24 JTAG
- 5.1.25 Cavium GPIO Control
- 5.1.26 Cavium GPIO Data Out
- 5.1.27 Cavium GPIO Data In
- 5.1.28 IPMP/IPMC GPIO Control
- 5.1.29 LPC Bus Control
- 5.1.30 LPC Data
- 5.1.31 Serial IRQ Interrupt 1
- 5.1.32 Serial IRQ Interrupt 2
- 5.1 MPC8548 PLD Register Summary
- Ethernet Interface
- System Management
- 7.1 Overview
- 7.2 IPMC Overview
- 7.3 IPMI Messaging
- 7.4 IPMB Protocol
- 7.5 SIPL Protocol
- 7.6 Message Bridging
- 7.7 Standard Commands
- 7.8 OEM Boot Options
- 7.9 IPMC Watchdog Timer Commands
- 7.10 FRU LEDs
- 7.11 Vendor Commands
- 7.11.1 Get Status
- 7.11.2 Get Serial Interface Properties
- 7.11.3 Set Serial Interface Properties
- 7.11.4 Get Debug Level
- 7.11.5 Set Debug Level
- 7.11.6 Get Hardware Address
- 7.11.7 Set Hardware Address
- 7.11.8 Get Handle Switch
- 7.11.9 Set Handle Switch
- 7.11.10 Get Payload Communication Time-Out
- 7.11.11 Set Payload Communication Time-Out
- 7.11.12 Enable Payload Control
- 7.11.13 Disable Payload Control
- 7.11.14 Reset IPMC
- 7.11.15 Hang IPMC
- 7.11.16 Bused Resource
- 7.11.17 Bused Resource Status
- 7.11.18 Graceful Reset
- 7.11.19 Diagnostic Interrupt Results
- 7.11.20 Get Payload Shutdown Time-Out
- 7.11.21 Set Payload Shutdown Time-Out
- 7.11.22 Set Local FRU LED State
- 7.11.23 Get Local FRU LED State
- 7.11.24 Update Discrete Sensor
- 7.11.25 Update Threshold Sensor
- 7.12 ASYNCHRONOUS EVENT NOTIFICATION
- 7.13 BOOT BANK SUPERVISION SENSOR
- 7.14 BOOT FIRMWARE BOOT OPTIONS
- 7.15 BOOT DEVICE REDIRECTION (BDR)
- 7.16 MESSAGE LISTENERS
- 7.17 System Firmware Progress Sensor
- 7.18 Entities and Entity Associations
- 7.19 Sensors and Sensor Data Records
- 7.20 FRU Inventory
- 7.21 E-Keying
- 7.22 HPM.1 Firmware Upgrade
- 7.23 IPMC Headers
- Back Panel Connectors
- Management Processor Monitor
- 9.1 Overview
- 9.2 Command-Line Features
- 9.3 Basic Operation
- 9.4 Monitor Recovery and Updates
- 9.5 Monitor Command Reference
- 9.6 Boot Commands
- 9.7 File Load Commands
- 9.8 Memory Commands
- 9.9 Flash Commands
- 9.10 EEPROM/I2C Commands
- 9.11 IPMC Commands
- 9.12 Environment Parameter Commands
- 9.13 Test Commands
- 9.14 Other Commands
- 9.14.1 autoscr
- 9.14.2 base
- 9.14.3 bdinfo
- 9.14.4 coninfo
- 9.14.5 crc32
- 9.14.6 date
- 9.14.7 echo
- 9.14.8 enumpci
- 9.14.9 go
- 9.14.10 help
- 9.14.11 iminfo
- 9.14.12 isdram
- 9.14.13 loop
- 9.14.14 memmap
- 9.14.15 moninit
- 9.14.16 pci
- 9.14.17 phy
- 9.14.18 ping
- 9.14.19 reset
- 9.14.20 run
- 9.14.21 script
- 9.14.22 showmac
- 9.14.23 showpci
- 9.14.24 sleep
- 9.14.25 switch_reg
- 9.14.26 version
- 9.14.27 vlan
- 9.15 MPC8548 Environment Variables
- 9.16 Troubleshooting
- 9.17 Download Formats
- A Related Documentation