Ashly mXa-1502 12-Channel 4-Zone DSP Mixer-Amplifier - Manual (Page 34)

Specifications
Maximum Output Power
CEA-2006/490A, 20ms 1kHz 1%THD+N, 480ms
1kHz -20dB, 120VAC all channels driven at
rated load ow Z output, per channel
Low Z output, per channel
8 Ohm 150W
4 Ohm 150W
2 Ohm 150W
Low Z output, per bridged channel pair
8 Ohm 300W
4 Ohm 300W
Hi-Z output, per channel
25V 150W
70V 150W
100V 150W
Hi-Z output, per bridged channel pair
25V 300W
70V 300W*
100V 300W*
*May require Class 3 speaker wiring,
all others use Class 2 wiring.
Total AC Mains Power Draw
Typical input, all channels driven, 120VAC
Sleep <1W
Standby 15W
Idle (no signal) 33W
1/8 max power, 2 Ohm 133W
AC Mains Current Draw
Typical input, all channels driven
120VAC (divide in half for 240V)
Sleep mode 0.094A
Standby mode 0.2A
Idle (no signal) 0.35A
1/8 max power, 70V 1.16A
Thermal Dissipation
in BTU/hour with typical input, all channels
driven, 120VAC
Sleep mode 2.14BTU/h
Standby 51BTU/h
Idle (no signal) 112BTU/h
1/8 max power, 2 Ohm 325BTU/h
Damping Factor ,
8 ohm load, <1kHz
>250
Distortion,
SMPTE, typical
<0.5%
Distortion,
THD-N, typical
<0.5%
Channel Separation,
dB from full output, 1kHz
-75 dB
Signal to Noise,
20Hz-20KHz, unweighted
>99 dB
Frequency Response 20Hz-20kHz, +/- 0.05dB
General Specifications
Mic/Line Input Euroblock 3.5mm
Input Impedance Active balanced, 18kΩ
Maximum Input Level +21dBu
Input Gain Range 0dB to +66dB
Phantom Power
+48V, software
switchable per channel
Stereo Line Input Dual RCA, unbalanced
Input Impedance 10.0KΩ
Maximum Input Level -10dBv (-7dBu)
AUX Output
Aux 1, Aux 2, Euroblock
3.5mm, balanced
AUX Out Maximum Level +21 dBu
Speaker Output
Euroblock 7.62mm
VCA 1-3 input
Euroblock 3.5mm
+1.8V, VCA pins 1-3, G
Data Connection
(
reserved for future use)
Euroblock 3.5mm
Data In/Out, +18V, Gnd
Trigger 1-8
contact closure input Euroblock 3.5mm
assignable function
GPO 1 & 2 general
purpose outputs Euroblock 3.5mm
assignable function
Amplifier Fault 1 & 2
logic outputs
High (+3V) when amp
channel is on and ok,
low (0V) when amp
channel is off or in a
protect/fault state
Remote Standby
Contact Closure Euroblock 3.5mm
close to engage standby
Ethernet RJ45, 100MB/1GB
Output Mode select
per amp channel
4 pos. DIP switch
Lo-Z - 4Ω, 8Ω
Hi-Z - 25V, 70V, 100V
Front Panel LED Features
Clip/Mute LED
Red, ON at max output
power, mute, level fully off
Signal LED
Green, ON at 18dB
below full output
Current LED
Green, ON when 0.5A
current delivered to
speaker load
Temp LED
Yellow, ON when
countermeasures
applied for excess heat
Power LED
White, ON, OFF,
Flashing for Standby
Com LED
Green, ON during
Ethernet activity
Protect LED
Red, ON for amp fault
causing shut-down
Sleep LED Blue, ON for sleep mode
Disable LED
Yellow, ON when power
switch disabled
Bridge LED
Green, ON when amp
is in bridge mode
Front Panel
Select Buttons
A, B, C, D, programmable
for source select or
preset recall
Factory reset switch see section 3.3
Processors
Input A/D: 24 bit
Output D/A: 24 bit
DSP Processors: 32-bit floating point
Sample Rate: 48kHz
Propagation Delay 1.42 ms
34
mXa-1502 • Operating Manual