Dremel Digilab 3D45-EDU Printer for Education - Manual (Page 3)

General Safety Warnings
3
Work Area Safety
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
Do not operate Dremel 3D45 in the presence
of flammable liquids, gases or dust. Dremel
3D45 creates high temperatures which may
ignite the dust or fumes.
Store idle 3D45 out of reach of children and
other untrained persons. Injury can occur in
hands of untrained users.
Electrical Safety
Always use the Dremel 3D45 with a properly
grounded outlet. Do not modify Dremel 3D45
plug. Improper grounding and modified plugs
increase risk of electric shock.
Do not use Dremel 3D45 in damp or wet
locations. Do not expose Dremel 3D45 to
rain. Presence of moisture increases risk of
electric shock.
Do not abuse the cord. Never use the cord
for pulling or unplugging the Dremel 3D45.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
Avoid using this product during an electric
storm. There may be a remote risk of a power
surge from lightning that may result in electric
shock hazard.
In case of emergency unplug Dremel 3D45
from outlet.
Personal Safety
Stay alert, watch what you are doing and
use common sense when operating a
Dremel 3D45. Do not use Dremel 3D45 while
you are tired or under the influence of drugs,
alcohol or medication. A moment of
inattention while operating Dremel 3D45 may
result in personal injury.
Use personal protective equipment. The use
of protective equipment such as heat resistant
gloves and safety glasses will reduce the risk of
personal injuries.
Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught in
moving parts.
Dremel 3D45 Use and Care
Before every use check Dremel 3D45 for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the Dremel 3D45’s operation.
If damage is suspected have the Dremel
3D45 repaired by authorized Dremel service
center before use. Use of Dremel 3D45 when
damaged may result in poor quality of object
creation, further equipment damage, property
damage or personal injury.
Do not touch the extruder tip or heated build
platform during Dremel 3D45 operation or until
it has cooled down to at least 60°C (140°F).
Contact with the extruder tip or build platform
during or after operation before tip and build plate
has cooled may result in personal injury.
Set up the Dremel 3D45 in a well-ventilated
area. Place Dremel 3D45 printer on flat
nonflammable surface and away from
flammable materal. Provide at least 8 inches
of unobstructed spacing around Dremel
3D45. Dremel 3D45 melts plastic during
building. Plastic odors emitted during Dremel
3D45 operation may irritate eyes and airways.
Locating Dremel 3D45 close to surrounding
objects prevents proper ventilation.
Do not reach inside the Dremel 3D45 while it
is in operation. Contact with Dremel 3D45
moving parts during operation may result in
poor build quality, equipment damage or
personal injury.
Always monitor the Dremel 3D45 during
operation. Use of Dremel 3D45 by persons
unfamiliar with these warnings and instructions
may result in equipment or property damage
and personal injury.
Use only DREMEL filament. Use of filament
not authorized by Dremel may result in
equipment, property damage, or personal injury.
Do not adjust extruder/nozzle setting to
exceed the maximum rated temperature of
the filament type being used. Heating filament
above recommended range can cause
emissions that may result in personal injury.
Read all instructions in this manual and familiarize yourself with the Dremel
3D45 before setup and use. Failure to comply with the warnings and
instructions may result in fire, equipment damage, property damage, or personal injury.
READ ALL INSTRUCTIONS
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
! WARNING
DM 2610047405AB 03-18_3D45 3/27/18 9:51 AM Page 3