ProSoft Technology MVI71-MNET - Manual (Page 108)

MVI71-MNET ♦ PLC Platform Index
Modbus TCP/IP Interface Module User Manual
Page 108 of 109
ProSoft Technology, Inc.
June 23, 2009
L
Ladder Logic • 41
LED Status Indicators • 7, 53
Limitation of Remedies ** • 104
LIMITED WARRANTY • 101
M
Main Logic Loop • 60
Main Menu • 46
MB Address in Device • 36
Minimum Command Delay • 30
MNET Client Command List Error Data • 86
MNET Client Specific Errors • 87
MNET MODBUS Command Structure • 33
MNET Server Port 2000 Status Error Locations • 85
MNET Server Port 2001 Error Locations • 86
MNET Server Port 502 Status Error Locations • 85
Modbus Database View • 49
MODBUS Exception Codes • 97
MODBUS Exception Responses • 96
Modbus Function • 36
Modbus Message Data • 23
Modbus Protocol Specification • 31, 49, 88
Module Communication Error Codes • 87
Module Configuration • 19
Module Data • 22
Module Entries • 26
Module Name • 27
Module Power Up • 59
Moving Back Through 5 Pages of Registers • 50
Moving Forward Through 5 Pages of Registers • 50
MVI (Multi Vendor Interface) Modules • 2
MVI71-MNET Status Data Definition for Side Connect
File • 82
N
Navigation • 45
Network Menu • 52
No Other Warranties • 105
Node IP Address • 35
Normal Data Transfer • 62
O
Opening the Command Error List Menu • 47
Opening the Command List Menu • 47
Opening the Database Menu • 47
Output Offset • 38
P
Package Contents • 10
Pass-Through Control Blocks • 67, 73
Pass-Through Mode • 28
Pinouts • 78, 81
Poll Interval • 34
Preset Multiple Registers (Function Code 16) • 95
Preset Single Register (Function Code 06) • 92
Printing a Configuration File • 27
Procedures for Return of Units Out of Warranty: • 100
Procedures for Return of Units Under Warranty: • 100
Product Specifications • 7, 57
ProSoft Configuration Builder • 23
ProSoft Technology® Product Documentation • 4
Purchasing Warranty Extension: • 101
R
Read Block • 62
Read Coil Status (Function Code 01) • 88
Read Holding Registers (Function Code 03) • 90
Read Input Registers (Function Code 04) • 90
Read Input Status (Function Code 02) • 89
Read Register Count • 27
Read Register Start • 27
Reading Status Data from the Module • 43
Receiving the Configuration File • 47
Redisplaying the Current Page • 49, 51
Redisplaying the Menu • 51
Reference • 7, 57
Reg Count • 34
Required Hardware • 43
Resetting diagnostic data • 47
Response Timeout • 30
Retry Count • 30
Return Material Authorization (RMA) Policies and
Conditions • 100
Returning to the Main Menu • 50, 51, 52
RS-232 Configuration/Debug Port • 79
S
Sending the Configuration File • 47
Server Driver • 75
Service Port • 35
Set Module Parameters • 26
Set Up the Project • 24
Setting Jumpers • 12
Side-Connect Backplane Data Transfer • 69
Slave Address • 35
Standard Modbus Protocol Errors • 87
Start Here • 7, 9
Status Data • 22
Status Data Structure for Database Storage • 83
Sub-function codes supported by the serial line
devices • 93
Support, Service & Warranty • 7, 99
Swap Code • 35
System Requirements • 9
T
The Configuration/Debug Menu • 44
Time Limit for Bringing Suit • 104
Transferring WATTCP.CFG to the module • 52
Transferring WATTCP.CFG to the PC • 52
Troubleshooting • 55
U
User Data • 22