Enterasys Networks Enterasys RoamAbout TRPZ-MP-422 User Manual
Page 15
CUSTOMER RELEASE NOTES
1/21/09 P/N: 9038177-27
Subject to Change Without Notice
Page: 15
of 28
F0615-O
Firmware Release 5.0.9.2:
Added support for the RBT-8210. This RAS, along with the current RBT-8200, will be known as the RBT-82x0
family.
Resolved an issue where DAPs would reset with an ASSERT error, due to traffic spikes in the network.
Resolved an issue where the RBT-1002-EU would crash with an ASSERT error after an image download.
Resolved an issue where a custom web page was not displayed after the client successfully authenticated
against the Access Point.
Resolved an issue where blank DNS and IP Router Fields in WebView resulted in a WebView IP Services error.
Resolved an issue where VLAN ports could not be selected in WebView.
Resolved an issue where the RAS would core dump after querying the rbtwsSysDataObjects MIB branch.
Resolved an issue where the RBT-4102-EU and the RBT-1002-EU were not supported in the country code
Hong Kong.
Resolved an issue when the RAS would report an SSL error or System communication errors after generating a
certificate signing request via WebView.
Resolved an issue when the current RAS configuration was not cleared after using the Quickstart feature via
WebView.
Resolved an issue where clients using a Macbook Pro could not connect to the RAS.
Resolved an issue where the Web portal login screen would not propagate to the client after a successful
authentication
Resolved an issue where one RAS configured for DAP load balancing and redundancy with a second RAS
continually reset after losing contact with configured DAPs.
Resolved an issue where the sixth (or more) DAP would crash using the Quickstart feature.
Resolved an issue when the switch received
an ARP packet with a source address of all zero‘s, it would cause a
tunnel crash.
Firmware Release 5.0.6.1:
Added support for the TRPZ-MXR-2 switch.
Resolved an issue where the DAP Operational Power was showing a N/A value for the country code Argentina.
Resolved an issue where an error message reading ―EAP_STORE_ERR‖ would appear on the CLI console of
the RBT-8110.
Resolved an issue where extra characters were added to the banner MOTD after a firmware upgrade on the
RAS.
Fixed an issue where a possible unicast flood condition could occur with redundant RBT-8400 switches.
Firmware Release 4.2.5.1:
Static IP configuration for DAPs
– These settings are only available through the CLI interface on the switch. The
user now can set a static IP address, RAS name or RAS address, and VLAN on the Access Points. These
settings are persistent on the RBT-1602 and the RBT-1002 Access Points only for the current 4.2.5.1 firmware.
Resolved an issue where the RBT-4102 and the RBT3K-AG would not boot due to an RSA fingerprint match
failure.
Resolved an issue with the WPA sequence number used to help sync up the per-packet keys between the Intel
3945 A/B/G chipsets and any Access Point in the RAS system. Clients would authenticate successfully against
the RADIUS server, but not have any connectivity to the network.
Resolved an issue where extra carriage returns in the banner MOTD would cause the RAS to fail an upgrade
and constantly reboot.
Resolved an issue where the RBT-8400 would core crash and lose part of the active configuration upon
upgrade.
Resolved an issue where the RAS
core crashed after cutting and pasting a ―set port group‖ CLI command.
Resolved an issue where the Quickstart configuration helper was automatically creating an admin password.
Fixed the length of the CLI entry for the mobility domain name from 16 to 32 characters.
Resolved a CLI command issue where the CLI would lock up after rapidly entering a ―show load‖ command (3-5
times within 5-10 seconds).