Main fuse chart – Whelen 9M144000 User Manual

Page 6

Page 6

May not be present on all Lightbars

Optional Equipment:

See

for fuse value

Main Fuse Chart

May not be present on all Lightbars

Optional Equipment:

See

for fuse value

Main Fuse Chart

GRN
BLU
GRN/WHT TRACE
BLU/WHT TRACE
WHT/GRN TRACE
WHT/BLU
YEL
WHT
WHT/BLK
WHT/BRN
GRN/BLK
WHT/ORG
WHT/YEL
BLU/BLK

Front Corner Strobes
Rear Corner Strobes

Rear Inboard Strobes
T.A. / 2 Strobe Flash

Passenger Alley Light
Driver Alley Light
Take-Down Lights
Flasher "A"
Right Traffic Advisor

Front Inboard Strobes

T.A. / 4 Strobe Flash

Auxiliary Option
Flashing Take-Downs
Left Traffic Advisor

3 amps
3 amps
3 amps
3 amps
3 amps
6 amps

2.5 amps
2.5 amps

5 amps
5 amps
6 amps
5 amps

2.5 amps

6 amps

GRN
BLU
GRN/WHT TRACE
BLU/WHT TRACE
GRN/BLK
BLU/BLK
YEL
WHT
WHIT/BLK
WHT/BRN
WHT/GRN
WHT/ORG
WHT/YEL
WHT/BLU
WHT/VIO

Front Corner Strobes
Rear Corner Strobes

Rear Inboard Strobes
Front Outboard Strobe
Rear
Passenger Alley Light
Driver Alley Light
Take-Down Lights
Flasher "A"

Front Inboard Strobes

Outboard Strobe

Flashers "B"
Auxiliary Option
Flashing Take-Downs
Work Lights
Flashing Work Lights

WIRE

FUNCTION

3 amps
3 amps
3 amps
3 amps
3 amps
3 amps

2.5 amps
2.5 amps

5 amps
5 amps
5 amps
5 amps

2.5 amps

5 amps

2.5 amps

CURRENT

DRAW

EXAMPLE: Using the WHITE/BLACK, WHITE,

& WHITE/ ORANGE function wires, the total amp

draw is

17.5 amps. Multiply this by 1.25 which

comes out to 21.87 amps. Y must fuse the

RED power wire at 25 amps.

To use the chart below: After determining which

function wires you will use, add up the amp rating

of each function wire. You must then multiply this

by 1.25 (see warning) and fuse the RED power

wire at this rating.

MAIN FUSE CHART

GREEN -

BLUE -

GREEN/WHITE TRACE -

BLUE/WHITE TRACE -

VIOLET -

YELLOW -

WHITE -

WHITE/ORANGE -

WHITE/BLACK -

WHITE/BROWN -

WHITE/YELLOW -

WHITE/BLUE -

NONE -

WHITE/VIOLET -

WHITE/RED -

In factory default configuration, this activates

RFI shield drain wire; connect to Ground

In factory default configuration, this activates

In the factory default configuration, this wire activates

In factory default configuration, this wire activates

In factory default configuration, this activates

his will initiate low power operation of all strobes

Front Corner Strobes

Rear Corner Strobes

Rear Inboard Strobes

Front Outboard Strobes

Rear Outboard Strobes

Passenger Alley Light

Driver Alley Light

9MH2 Take-Down Lights*

Front Inboard Strobes

(See: Low Power Violet)

9MTD2 Take-Down Lights*

Flasher "A" *

Flasher "B"

Flashing Take-Downs*

Work Lights*

Flashing Work Lights

Not Used

GREEN/BLACK

BLUE/BLACK

WHITE/GREEN

or Aux. Lights

not used if 9MTD2 is present

GREEN -

BLUE -

GREEN/WHITE TRACE -

BLUE/WHITE TRACE -

WHITE/GREEN TRACE -

WHITE/BLUE -

VIOLET -

YELLOW -

WHITE -

WHITE/ORANGE -

WHITE/BLACK -

WHITE/BROWN -

GREEN/BLACK -

WHITE/YELLOW -

BLUE/BLACK -

NONE -

WHITE/RED -

In the factory default configuration, this wire activates

In factory default configuration, this wire activates

In factory default configuration, this activates

This will initiate low power operation of all strobes

In factory default configuration, this activates

RFI shield drain wire; connect to Ground

Front Corner Strobes

Rear Corner Strobes

Front Inboard Strobes

Rear Inboard Strobes

2 Strobe T.A. Flash

4 Strobe T.A. Flash

See: Low Power Violet

Passenger Alley Light *

Driver Alley Light *

9MTD2 Take-Down Lights *

9MH2 Take-Down Lights *

Flasher "A"

Right Traffic Advisor *

Flashing Take-Downs *

Left Traffic Advisor *

Not Used

or Aux. Lights

not used if 9MTD2 is present

CONTROL

CABLE

CONTROL

CABLE

NONE - RFI Shield Drain

BLACK - Ground/8 AWG

RED - +12 VDC/8 AWG

POWER

CABLE

POWER

CABLE

EDGE® 9M SERIES LIGHTBAR for MODELS EQUIPPED with STROBE TRAFFIC ADVISOR™

EDGE® 9M SERIES LIGHTBAR

WIRE

FUNCTION

CURRENT

DRAW

EXAMPLE: Using the WHITE/BLACK, WHITE,

& WHITE/ ORANGE function wires, the total amp

draw is

17.5 amps. Multiply this by 1.25 which

comes out to 21.87 amps. Y must fuse the

RED power wire at 25 amps.

To use the chart below: After determining which

function wires you will use, add up the amp rating

of each function wire. You must then multiply this

by 1.25 (see warning) and fuse the RED power

wire at this rating.

MAIN FUSE CHART

This manual is related to the following products:

9M148000 9M142000 9M14400F 9M14800F 9M14200F 9M264000 9M268000 9M262000 9M284000 9M288000 9M282000 9M304000 9M308000 9M302000 9M324000 9M328000 9M322000 9MMEDGEP 9MMEDGEM